| LANZHOU LS-NATIONAL OIL WELL PETROLEUM ENGINEERING CO. LTD. | |
| ZP 175 ZP205 ZP275 ZP375 ROTARY TABLE PARTS LIST | |
| ZP175 ROTARY TABLE PARTS LIST | |
| Part Name | Part NO. |
| ROTARY TABLE | 105.11.00-1 |
| Lock pawl—left | 105.06.01 |
| Lock pawl—right | 105.06.02 |
| Pin,handle lock pawl | 105.06.03-1 |
| Grease fitting | GB1152-89 (Ml 0X1) |
| Grease fitting | |
| Pin, lock pawl | 105.11.01 |
| Plug | 105.06.05 (1/8″) |
| Screw, hex soc hd | 105.06.10.00 |
| Grease fitting | GB70-85 (M24X75) |
| Plate, I.D | 105.11.27 |
| Screw | GB67-85 (M4X8) |
| Dipstick,oi1 | 105.11.10.00 |
| Plug | 105.06.07 (1 1/2″) |
| Housing | 105.11.20.00 |
| Tongue | 105.11.03 |
| Cover | 105.11.30.00 |
| Ring gear (spiral teeth) | 105.11.31 |
| Ring gear (beveling teeth) | 105.11.28 |
| Bearing | 91682/530 |
| Table | 105.11.05-1 |
| Table installation | |
| Ring gear (sprial teeth) | |
| Table | |
| Bearing | |
| Columnar pin | |
| Support, bearing | |
| ROTARY TABLE | 105.11.00-1 |
| 0-Ring | |
| Screw | |
| Washer, spring | |
| Shim | |
| Shim | |
| Shim | |
| Lock pawl | 105.11.50.00 |
| Pin | 105.11.24 |
| Pin, cotter 5X36 | GB91-86 |
| Pin,cotter 5X36 | |
| Kelly bushing | 105.11.30 (3 1/2″) |
| Kelly bushing | 105.11.32 (5″) |
| Kelly bushing installatior | |
| Kelly bushing | |
| Board | |
| Pin | |
| Master bushing | 105.11.29 |
| Bearing | 1689/520 |
| Shim | |
| Shim | |
| Shim | 105.11.10 |
| Pinion shaft assembly | 105.11.40.00 |
| Drain plug | |
| Seal | 105.11.18 |
| 0-Ring | 105.11.14 |
| Screw | 105.11.17 (M20X65) |
| Washer,spring 20 | GB93-87 |
| Shim | 105.11.15 |
| Shim | 105.11.16 |
| Support,bearing | 105.11.12 |
| Screw | GB5783-86 (Ml 6X40) |
| Washer, spring 16 | GB93-87 |
| SIinger | 105.11.13 |
| 0-Ring | 105.11.11 |
| Chain wheel | 105.11.2H |
| Sprocket retainer | |
| Flange | 105.11.19 |
| Main kelly bushing installation | |
| Main kelly bushing | |
| Spacer | |
| Board | |
| Screw | |
| Nut | |
| Washer,sping 28X35X2 | |
| ValveDN32 (1 1/4″) | |
| Joint R1 1/4 | |
| ROTARY TABLE | 105.11.00-1 |
| Pinion Shaft Assembly | 105.11.40.00 |
| Pinion Shaft Assembly | 105.11.40.00 |
| Pinion (beveling teeth) | 105.11.40.12 |
| Pinion (spiral teeth) | 105.11.40.13 |
| Retainer,pinion end | |
| End-plate of bearing | 105.11.40.02 |
| Bearing | 32622EH |
| 0-Ring | 105.11.40.03 |
| Spacer | 105.11.40.04 |
| Drain plug 1″ | |
| Drain plug | 105.08.60.01 |
| Magnet | 105.08.60.02 |
| Pin, cotter 2X12 | GB91-86 |
| Shaft,pinion | 105.11.40.05 |
| Bearing | 53622H |
| Screw | |
| Screw | GB5783-86 (M20X60) |
| Screw | GB5783-86 (Ml 6X50) |
| Washer,spring 20 | |
| Washer,spring 20 | GB93-87 |
| Washer, spring 16 | GB93-87 |
| Shim | 105.11.40.06 |
| Capsule | 105.11.41.00 |
| Shim | 105.11.40.07 |
| Pinion Shaft Assembly | 105.11.40.00 |
| Sea 1, o i 1 | D7-1-67 (140X170X15) |
| Retainer,pinion end | |
| Retainer,pinion end | 105.11.40.10 |
| Nut,pinion shaft | |
| Pinion shaft housing | 105.11.40.08 |
| Key | 105.11.40.09 |
| Sprocket retainer | C6-3-92 (125) |
| Screw with head holes | |
| Screw with head holes | GB32.1-88 |
| Screw with head holes | |
| Wire | |
| Shim | |
| Shim | |
| Screw with head holes | |
| ZP205 ROTARY TABLE PARTS LIST | |
| Part Name | |
| ROTARY TABLE | 105.07.00 |
| Lock pawl—left | 105.06.01 |
| Lock pawl—right | 105.06.02 |
| Pin,handle lock pawl | 105.06.03-1 |
| Grease fitting | GB1152-89 ( M10X1) |
| Grease fitting | |
| Pin, lock pawl | 105.07.0H |
| Plug | 105.06.05 (1/8″) |
| Screw, hex soc hd | 105.06.10.00 |
| Grease fitting | GB70-85 (M24X75) |
| Plate, I.D | 105.07.19 |
| Screw | GB67-85 (M4X8) |
| Dipstick,oi1 | 105.07.40.00 |
| Plug | 105.06.07 (1 1/2″) |
| Housing | 105.07.10.00 |
| Tongue | 105.06.08 |
| Cover | 105.07.20.00 |
| Ring gear (spiral teeth) | 105.07.21 |
| Ring gear (beveling teeth) | 105.07.20 |
| Bearing | 1687/650 |
| Table | 105.07.06 |
| Table installation | |
| Ring gear (sprial teeth) | |
| Table | |
| Bearing | |
| Columnar pin | |
| Support, bearing | |
| ROTARY TABLE | 105.07.00 |
| 0-Ring | |
| Screw | |
| Washer, spring | |
| Shim | |
| Shim | |
| Shim | |
| Lock pawl | 105.05.18 |
| Pin | 105.05.19 |
| Pin, cotter 5X36 | GB91-86 |
| Pin,cotter 5X36 | |
| Kelly bushing | 105.06.31 (5″) |
| Kelly bushing | |
| Kelly bushing installatior | |
| Kelly bushing | |
| Board | |
| Pin | |
| Master bushing | 105.07.22 |
| Bearing | 1687/620 |
| Shim | 105.07.08 |
| Shim | |
| Shim | |
| Pinion shaft assembly | 105.07.30.00 |
| Drain plug | 104.05.19 |
| Seal | 105.07.09 |
| 0-Ring | 105.07.10 |
| Screw | 105.07.17 (M20X70) |
| Washer,spring 20 | GB93-87 |
| Shim | 105.07.11 |
| Shim | 105.07.12 |
| Support,bearing | 105.07.13 |
| Screw | GB5783-86 (Ml 6X45) |
| Washer, spring 16 | GB93-87 |
| SIinger | 105.07.14 |
| 0-Ring | 105.07.15 |
| Chain wheel | 105.07.16 |
| Sprocket retainer | 105.06.24 |
| Flange | 105.06.25 |
| Main kelly bushing installation | |
| Main kelly bushing | |
| Spacer | |
| Board | |
| Screw | |
| Nut | |
| Washer,sping 28X35X2 | |
| ValveDN32 (1 1/4″) | |
| Joint R1 1/4 | |
| ROTARY TABLE | 105.07.00 |
| Pinion Shaft Assembly | 105.07.30.00 |
| Pinion Shaft Assembly | 105.07.30.00 |
| Pinion (beveling teeth) | 105.07.30.10 |
| Pinion (spiral teeth) | 105.07.30.11 |
| Retainer,pinion end | 105.06.51.00 |
| End-plate of bearing | |
| Bearing | 32630 |
| 0-Ring | D4-5-73 (420X8.6) |
| Spacer | 105.07.30.03 |
| Drain plug 1″ | 104.05.19 |
| Drain plug | |
| Magnet | |
| Pin, cotter 2X12 | |
| Shaft,pinion | 105.07.30.04 |
| Bearing | 3630 |
| Screw | GB5783-86 (M20X70) |
| Screw | |
| Screw | |
| Washer,spring 20 | GB93-87 |
| Washer,spring 20 | |
| Washer, spring 16 | |
| Shim | 105.06.50.04 |
| Capsule | 105.07.30.05 |
| Shim | 105.07.30.06 |
| Pinion Shaft Assembly | 105.07.30.00 |
| Sea 1, o i 1 | D7-1-67 (180X220X15) |
| Retainer,pinion end | 105.06.50.07 |
| Retainer,pinion end | |
| Nut,pinion shaft | 105.06.50.08 |
| Pinion shaft housing | |
| Key | 105.06.50.09-1 |
| Sprocket retainer | C6-1-72 (150) |
| Screw with head holes | GB32.1-88 |
| Screw with head holes | |
| Screw with head holes | |
| Wire | |
| Shim | 105.07.30.07 |
| Shim | 105.07.30.08 |
| Screw with head holes | |
| ZP275 ROTARY TABLE PARTS LIST | |
| Part Name | |
| ROTARY TABLE | 105.06.00 |
| Lock pawl—left | 105.06.01 |
| Lock pawl—right | 105.06.02 |
| Pin,handle lock pawl | 105.06.03-1 |
| Grease fitting | GB1152-89 ( Ml 0X1) |
| Grease fitting | |
| Pin, lock pawl | 105.06.04-1 |
| Plug | 105.06.05 (1/8″) |
| Screw, hex soc hd | 105.06.10.00 |
| Grease fitting | GB70-85 (M24X75) |
| Plate, I.D | 105.06.30-1 |
| Screw | GB67-85 (M4X8) |
| Dipstick,oi1 | 105.06.20.00 |
| Plug | 105.06.07 (1 1/2″) |
| Housing | 105.06.30.00 |
| Tongue | 105.06.08 |
| Cover | 105.06.40.00 |
| Ring gear (spiral teeth) | 105.06.33 |
| Ring gear (beveling teeth) | 105.06.34 |
| Bearing | 91682/800 |
| Table | 105.06.10 |
| Table installation | |
| Ring gear (sprial teeth) | |
| Table | |
| Bearing | |
| Columnar pin | |
| Support, bearing | |
| ROTARY TABLE | 105.06.00 |
| 0-Ring | |
| Screw | 105.06.22 |
| Washer, spring | GB93-87 |
| Shim | |
| Shim | |
| Shim | |
| Lock pawl | 105.05.18 |
| Pin | 105.05.19 |
| Pin, cotter 5X36 | GB91-86 |
| Pin,cotter 5X36 | |
| Kelly bushing | 105.06.31 (5″) |
| Kelly bushing | |
| Kelly bushing installatior | |
| Kelly bushing | |
| Board | |
| Pin | |
| Master bushing | 105.06.32 |
| Bearing | 1681/800 |
| Shim | |
| Shim | 105.06.13 |
| Shim | |
| Pinion shaft assembly | 105.06.50.00 |
| Drain plug | 104.05.19 |
| Seal | 105.06.14 |
| 0-Ring | 105.06.15 |
| Screw | 105.06.22 (M24X70) |
| Washer,spring 20 | |
| Shim | 105.06.16 |
| Shim | 105.06.17 |
| Support,bearing | 105.06.18 |
| Screw | GB5783-86 (Ml 6X40) |
| Washer, spring 16 | GB93-87 |
| SIinger | 105.06.19 |
| 0-Ring | 105.06.20 |
| Chain wheel | 105.06A. 01-1 |
| Sprocket retainer | 105.06.24 |
| Flange | 105.06.25 |
| Main kelly bushing installation | |
| Main kelly bushing | |
| Spacer | |
| Board | |
| Screw | |
| Nut | |
| Washer,sping 28X35X2 | |
| ValveDN32 (1 1/4″) | |
| Joint R1 1/4 | |
| ROTARY TABLE | 105.06.00 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Pinion (beveling teeth) | 105.06.50.12 |
| Pinion (spiral teeth) | 105.06.50.13 |
| Retainer,pinion end | 105.06.51.00 |
| End-plate of bearing | |
| Bearing | 32630 |
| 0-Ring | D4-5-73 (420X8.6) |
| Spacer | 105.06.50.02 |
| Drain plug 1″ | 104.05.19 |
| Drain plug | |
| Magnet | |
| Pin, cotter 2X12 | |
| Shaft,pinion | 105.06.50.03 |
| Bearing | 3630 |
| Screw | GB5783-86 (M20X60) |
| Screw | |
| Screw | |
| Washer,spring 20 | GB93-87 |
| Washer,spring 20 | |
| Washer, spring 16 | |
| Shim | 105.06.50.04 |
| Capsule | 105.06.50.05-1 |
| Shim | 105.06.50.06 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Sea 1, o i 1 | D7-1-67 (180X220X15) |
| Retainer,pinion end | 105.06.50.07 |
| Retainer,pinion end | |
| Nut,pinion shaft | 105.06.50.08 |
| Pinion shaft housing | |
| Key | 105.06.50.09-1 |
| Sprocket retainer | C6-1-72 (150) |
| Screw with head holes | GB32.1-88 |
| Screw with head holes | |
| Screw with head holes | |
| Wire | |
| Shim | |
| Shim | |
| Screw with head holes | |
| ZP275-2 ROTARY TABLE PARTS LIST | |
| Part Name | |
| ROTARY TABLE | 105.10.00 |
| Lock pawl—left | 105.06.01 |
| Lock pawl—right | 105.06.02 |
| Pin,handle lock pawl | 105.06.03-1 |
| Grease fitting | GB1152-89 ( Ml 0X1) |
| Grease fitting | |
| Pin, lock pawl | 105.06.04-1 |
| Plug | 105.06.05 (1/8″) |
| Screw, hex soc hd | 105.06.10.00 |
| Grease fitting | GB70-85 (M24X75) |
| Plate, I.D | 105.10.03 |
| Screw | GB67-85 (M4X8) |
| Dipstick,oi1 | 105.06.20.00 |
| Plug | 105.06.07 (1 1/2″) |
| Housing | 105.06.30.00 |
| Tongue | 105.06.08 |
| Cover | 105.06.40.00 |
| Ring gear (spiral teeth) | 105.06.33 |
| Ring gear (beveling teeth) | 105.06.34 |
| Bearing | 91682/800 |
| Table | 105.06.10 |
| Table installation | |
| Ring gear (sprial teeth) | |
| Table | |
| Bearing | |
| Columnar pin | |
| Support, bearing | |
| ROTARY TABLE | 105.10.00 |
| 0-Ring | |
| Screw | 105.06.22 |
| Washer, spring | GB93-87 |
| Shim | |
| Shim | |
| Shim | |
| Lock pawl | 105.05.18 |
| Pin | 105.05.19 |
| Pin, cotter 5X36 | GB91-86 |
| Pin,cotter 5X36 | |
| Kelly bushing | 105.06.31 (5″) |
| Kelly bushing | |
| Kelly bushing installatior | |
| Kelly bushing | |
| Board | |
| Pin | |
| Master bushing | 105.06.32 |
| Bearing | 1681/800 |
| Shim | |
| Shim | 105.06.13 |
| Shim | |
| Pinion shaft assembly | 105.06.50.00 |
| Drain plug | 104.05.19 |
| Seal | 105.06.14 |
| 0-Ring | 105.06.15 |
| Screw | 105.06.22 (M24X70) |
| Washer,spring 20 | |
| Shim | 105.06.16 |
| Shim | 105.06.17 |
| Support,bearing | 105.06.18 |
| Screw | GB5783-86 (Ml 6X40) |
| Washer, spring 16 | GB93-87 |
| SIinger | 105.06.19 |
| 0-Ring | 105.06.20 |
| Chain wheel | |
| 105.10.01.00 | |
| Sprocket retainer | 105.06.24 |
| Flange | 105.06.25 |
| Main kelly bushing installation | |
| Main kelly bushing | |
| Spacer | |
| Board | |
| Screw | |
| Nut | |
| Washer,sping 28X35X2 | |
| ValveDN32 (1 1/4″) | |
| Joint R1 1/4 | |
| ROTARY TABLE | 105.10.00 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Pinion (beveling teeth) | 105.06.50.12 |
| Pinion (spiral teeth) | 105.06.50.13 |
| Retainer,pinion end | 105.06.51.00 |
| End-plate of bearing | |
| Bearing | GB283-64 (32630) |
| 0-Ring | D4-5-73 (420X8.6) |
| Spacer | 105.06.50.02 |
| Drain plug 1″ | 104.05.19 |
| Drain plug | |
| Magnet | |
| Pin, cotter 2X12 | |
| Shaft,pinion | 105.06.50.03 |
| Bearing | 3630 |
| Screw | GB5783-86 (M20X60) |
| Screw | |
| Screw | |
| Washer,spring 20 | GB93-87 |
| Washer,spring 20 | |
| Washer, spring 16 | |
| Shim | 105.06.50.04 |
| Capsule | 105.06.50.05-1 |
| Shim | 105.06.50.06 |
| Pinion Shaft Assembly | 105.06.50.00 |
| Sea 1, o i 1 | D7-1-67 (180X220X15) |
| Retainer,pinion end | 105.06.50.07 |
| Retainer,pinion end | |
| Nut,pinion shaft | 105.06.50.08 |
| Pinion shaft housing | |
| Key | 105.06.50.09-1 |
| Sprocket retainer | C6-1-72 (150) |
| Screw with head holes | GB32.1-88 |
| Screw with head holes | |
| Screw with head holes | |
| Wire | |
| Shim | |
| Shim | |
| Screw with head holes | |
| ZP375 ROTARY TABLE PARTS LIST | |
| Part Name | |
| ROTARY TABLE | 105.08.00 |
| Lock pawl—left | 105.06.01 |
| Lock pawl—right | 105.06.02 |
| Pin,handle lock pawl | 105.06.03-1 |
| Grease fitting | |
| Grease fitting | GB1152-89 (Ml 0x1) |
| Pin, lock pawl | 105.08.10-1 |
| Plug | 105.06.05 (1/8″) |
| Screw, hex soc hd | 105.06.10.00 |
| Grease fitting | GB70-85 (M24x75) |
| Plate, I.D | 105.08.20 |
| Screw | GB67-85 (M4x8) |
| Dipstick,oi1 | 105.08.30.00 |
| Plug | 105.06.07 (1 1/2″) |
| Housing | 105.08.20.00 |
| Tongue | 105.06.08 |
| Cover | 105.08.10.00 |
| Ring gear (spiral teeth) | |
| Ring gear (beveling teeth) | |
| Bearing | |
| Table | |
| Table installation | 105.08.40.00 |
| Ring gear (sprial teeth) | 105.08.40.11 |
| Table | 105.08.40.02 |
| Bearing | 2687/1049 |
| Columnar pin | 105.08.40.03 |
| Support, bearing | 105.08.40.04 |
| ROTARY TABLE | 105.08.00 |
| 0-Ring | 105.08.40.05 |
| Screw | GB70-85 (M24x60) |
| Washer, spring | GB93-87 (24) |
| Shim | 105.08.40.06 |
| Shim | 105.08.40.07 |
| Shim | 105.08.40.08 |
| Lock pawl | 105.08.02 |
| Pin | 105.05.19 |
| Pin, cotter 5X36 | |
| Pin,cotter 5X36 | GB91-86 (5×36) |
| Kelly bushing | |
| Kelly bushing | |
| Kelly bushing installatior | 105.54.00 (2 3/8″~8 5/8″) |
| Kelly bushing | 105.54.01 |
| Board | 105.54.02 |
| Pin | 105.54.03 |
| Master bushing | |
| Bearing | |
| Shim | |
| Shim | |
| Shim | 105.08.08 |
| Pinion shaft assembly | 105.08.50.00 |
| Drain plug | |
| Seal | |
| 0-Ring | |
| Screw | |
| Washer,spring 20 | |
| Shim | |
| Shim | |
| Support,bearing | |
| Screw | GB5783-86 (Ml 6X35) |
| Washer, spring 16 | GB93-87 (16) |
| SIinger | 105.08.09 |
| 0-Ring | |
| Chain wheel | 105.08.07 |
| Sprocket retainer | 105.08.14 |
| Flange | 105.08.15 |
| Main kelly bushing installation | 105.08.07.00 |
| Main kelly bushing | 105.08.70.04 |
| Spacer | 105.08.70.02 |
| Board | 105.08.70.03 |
| Screw | 105.08.03 |
| Nut | 105.08.04 |
| Washer,sping 28X35X2 | D3-3-67 (28x35x2) |
| ValveDN32 (1 1/4″) | GB8465.1-87 (DN32 1 1/4″) |
| Joint R1 1/4 | GB3289.26-82 (R1 1/4) |
| ROTARY TABLE | 105.08.00 |
| Pinion Shaft Assembly | 105.08.50.00 |
| Pinion Shaft Assembly | 105.08.50.00 |
| Pinion (beveling teeth) | |
| Pinion (spiral teeth) | 105.08.50.12 |
| Retainer,pinion end | |
| End-plate of bearing | 105.08.50.09 |
| Bearing | GB283-64 (32630) |
| 0-Ring | 105.08.50.02 (470×8.6) |
| Spacer | 105.08.50.04 |
| Drain plug 1″ | 105.08.60.00 |
| Drain plug | 105.08.60.01 (1″) |
| Magnet | 105.08.60.02 |
| Pin, cotter 2X12 | GB91-86 (2×12) |
| Shaft,pinion | 105.08.50.03 |
| Bearing | GB286-64 (3630) |
| Screw | GB5783-86 (M20X60) |
| Screw | |
| Screw | |
| Washer,spring 20 | GB93-87 (20) |
| Washer,spring 20 | |
| Washer, spring 16 | |
| Shim | 105.08.50.05 |
| Capsule | 105.08.51.00 |
| Shim | 105.08.50.06 (4> 400/322 6 1) |
| Pinion Shaft Assembly | 105.08.50.00 |
| Sea 1, o i 1 | D7-1-67 (180X220X15) |
| Retainer,pinion end | 105.08.50.07 |
| Retainer,pinion end | |
| Nut,pinion shaft | |
| Pinion shaft housing | 105.08.50.10 |
| Key | 105.08.50.08 |
| Sprocket retainer | 105.08.50.11 (150) |
| Screw with head holes | |
| Screw with head holes | |
| Screw with head holes | GB32.1-88 (HI 6×35) |
| Wire | |
| Shim | |
| Shim | |
| Screw with head holes | GB32.1-88 |
Rotarytableparts2
Posted in InventoryList.