| Farr Style Tong KT14000 (50K) | ||||
| Lay Gear Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Grease Fitting | 1 | |
| 2 | 02-0093 | 1/8″ NPT 90 Degree Grease Fitting | 2 | |
| 3 | 09-1170 | 3/8″ NC x 1″ Hex Bolt | 4 | |
| 4 | 09-5006 | 3/8″ Plain Narrow Washer | 4 | |
| 5 | 1393-151 | Drive Shaft Bearing Cap | 1 | |
| 6 | 1393-151-04 | Bearing | 1 | |
| 7 | 1393-82-03 | Shaft Spacer | 1 | |
| 8 | 1393-81 | Drive Shaft Gear | 1 | |
| 9 | 1393-152 | Bottom Drive Shaft Bearing | 1 | |
| 10 | 1393-82-04 | Bottom Spacer | 1 | |
| 11 | 1393-80 | Drive Shaft Pinion Gear | 1 | |
| 12 | 1393-82 | Drive Shaft | 1 | |
| 13 | 1393-82-02 | Square Key 3/8″ x 3/8″ c 2-1/2″ | 2 | |
| Motor Mount Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 87-0130 | Rinner GA37-26 Hydraulic Motor | 1 | |
| 2 | Square 1/2″ x 1/2″ x 2″ Motor Gear Key | 2 | ||
| 3 | 1393-149 | Motor Gear | 1 | |
| 4 | 09-0107 | 1/4″ NC x 3/8″ Hex Socket Set Screw | 2 | |
| 5 | 101-1783 | Torque Gauge Mount Weldment | 1 | |
| 6 | 09-2170 | 1/2″ NC x 1-1/2″ Hex Socket Head Cap Screw | 2 | |
| 7 | 101-1621 | Gauge Mount Weldment | 1 | |
| 8 | 09-0090 | 0.148 x 2.938 Hitch Pin | 1 | |
| 9 | 101-1808 | Motor Mount Wildman | 1 | |
| 10 | 09-1292 | 3/4″ NC 1-3/4″ Hex Bolt | 4 | |
| 11 | 09-5118 | 3/4″ Carbon Steel Lockwasher | 4 | |
| 12 | 02-0005 | 1/8″ NPT Grease Fitting | 3 | |
| 13 | 02-0093 | 1/8″ NPT x 90 Degree Grease Fitting | 2 | |
| 14 | 09-1170 | 3/8″ NC x 1″ Hex Bolt | 4 | |
| 15 | 09-5006 | 3/8″ Carbon Steel Lockwasher | 4 | |
| 16 | 1393-151 | Lay Gear Bearing Cap | 1 | |
| 17 | 09-2170 | 1/2″ NC x 1-1/4″ Hex Socket Head Cap Screw | 6 | |
| Clutch Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 09-4007 | 1/4″ NC x 1″ Hex FHCS | 1 | |
| 2 | 1393-50-04 | Clutch Shaft Plate | 1 | |
| 3 | 1393-61 | Clutch Drive Gear | 1 | |
| 4 | 101-1947 | Gear Key | 2 | |
| 5 | 1393-50-03 | Clutch Shaft Spacer | 1 | |
| 6 | 09-4046 | 3/8″ NC x 1″ Hex Socket FHCS | 2 | |
| 7 | 1393-57 | Clutch Bearing Plate | 1 | |
| 8 | 1393-56 | Top Clutch Shaft Bearing | 1 | |
| 9 | 1393-50-01 | Clutch Shaft Spacer | 1 | |
| 10 | 1393-52 | Low Clutch Gear | 1 | |
| 11 | 1393-53 | Clutch Gear Needle Bearing | 4 | |
| 12 | 1393-52-01 | Inner Spacer | 1 | |
| 13 | 09-1557 | 3/8″ NC x 1-3/4″ Hex Bolt | 4 | |
| 13 | 09-5006 | 3/8″ Lockwashers | 4 | |
| 14 | 02-0005 | 1/8″ NPT Grease Fitting | 3 | |
| 15 | 1393-54 | Clutch Bearing Cap | 1 | |
| 16 | 1393-55 | Lower Clutch Bearing | 1 | |
| 17 | 1393-50-02 | Clutch Shaft Spacer | 1 | |
| 18 | 1393-51 | High Clutch Gear | 1 | |
| 19 | 1393-50 | Clutch Shaft | 1 | |
| 20 | 1393-62 | Shifting Collar | 1 | |
| Pinion Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0093 | 1/8″ NPT 90 Degree Grease Fitting | 4 | |
| 2 | 09-1170 | 1/2″ NC x 1-1/2″ Hex Bolts | 8 | |
| 3 | 09-5110 | 1/2″ Lockwashers | 8 | |
| 4 | 1393-89 | Top Pinion Bearing Cap | 1 | |
| 5 | 1393-93 | Pinion Bearing | 2 | |
| 6 | 1393-94 | Pinion Gear Spacer | 2 | |
| 7 | 1393-88 | High Pinion Gear | 1 | |
| 8 | 1393-86 | Pinion Gear | 1 | |
| 9 | 1393-89A | Lower Pinion Bearing Cap | 1 | |
| 10 | 1393-87 | Low Pinion Gear | 1 | |
| Pinion Idler Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | Grease Fitting, 1/8″ NPT | 1 | |
| 2 | 09-5740 | 1-1/2″ NF Nylock Nut | 1 | |
| 3 | 09-0081 | 5/8″ NC x 2-1/2″ Hex Bolt | 3 | |
| 4 | 09-5114 | 5/8″ Carbon Steel Lockwasher | 3 | |
| 5 | 997-D17-109 | Pinion Idler Pad | 1 | |
| 6 | 1050-D5-105 | Idler Half Shaft | 1 | |
| 7 | 02-0009 | Retainer Ring | 2 | |
| 8 | 997-A2-119 | Idler Gear | 1 | |
| 9 | 02-0011 | Idler Bearing | 1 | |
| 10 | 02-0008 | Idler Bearing Retainer | 1 | |
| 11 | 02-0010 | Bearing Seal | 1 | |
| Low-Profile Support Roller | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 1429-131-04 | 1-3/16″ External Snap Ring | 2 | |
| 3 | 1393-140 | Shaft Spacer | 2 | |
| 4 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 5 | 1393-131-01 | Support Roller Shaft | 1 | |
| 6 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 7 | 1393-135 | Support Roller | 1 | |
| Rotary Idler Assemly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | Grease Fitting, 1/8″ NPT | 1 | |
| 2 | 09-5740 | 1-1/2″ NC Nylock Nut | 2 | |
| 3 | 09-5040 | 1-1/2″ Washer | 2 | |
| 4 | 1393-121 | Idler Gear Spacer | 2 | |
| 5 | 1393-117 | Rotary Idler Shaft | 1 | |
| 6 | 1393-106 | Cylindrical Roller Bearing | 2 | |
| 7 | 1393-109 | Outer Idler Spacer | 1 | |
| 8 | 1393-110 | Retainer Ring | 1 | |
| 9 | 1393-119 | Idler Gear | 1 | |
| 10 | 1393-108 | Internal Spacer | 1 | |
| Support Roller 2 | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 09-9266 | 1″ Standard UNS Hex Nylock Nut | 2 | |
| 3 | 09-5120 | 1″ Narrow Washer | 2 | |
| 4 | 1393-140 | Shaft Spacer | 2 | |
| 5 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 6 | 1393-131 | Support Roller Shaft | 1 | |
| 7 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 8 | 1393-135 | Support Roller | 1 | |
| Support Roller | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 09-9266 | 1″ Standard UNS Hex Nylock Nut | 2 | |
| 3 | 09-5120 | 1″ Narrow Washer | 2 | |
| 4 | 1393-140 | Shaft Spacer | 2 | |
| 5 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 6 | 1393-131 | Support Roller Shaft | 1 | |
| 7 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 8 | 1393-135A | Support Roller | 1 | |
| Support Roller (Brake Band Support) | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 1429-131-04 | 1-3/16″ External Snap Ring | 2 | |
| 3 | 1393-140 | Shaft Spacer | 2 | |
| 4 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 5 | 1393-131-02 | Support Roller Shaft | 1 | |
| 6 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 7 | 1393-135 | Support Roller | 1 | |
| Support Roller (Torn Counter Clearance) | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 09-9266 | 1″ Standard UNS Hex Nylock Nut | 2 | |
| 3 | 09-5120 | 1″ Narrow Washer | 2 | |
| 4 | 1393-140 | Shaft Spacer | 2 | |
| 5 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 6 | 1393-131 | Support Roller Shaft | 1 | |
| 7 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 8 | 1393-135B | Support Roller | 1 | |
| Rotary Gear | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 1393-40 | Backing Pin Retainer Plate | 1 | |
| 2 | 09-5721 | 7/8″ NC Nylock Nut | 1 | |
| 3 | 1393-28 | Jaw Pivot Bolt | 2 | |
| 4 | 09-5822 | 7/8″ NC Hex Nut | 3 | |
| 5 | 1393-36 | Rear Cageplate Bolt | 1 | |
| 6 | 19-1326 | 3/4″ NC x 10″ Hex Bolt | 2 | |
| 7 | 02-0005 | 1/8″ NPT Grease Fitting | 8 | |
| 8 | 1393-21 | Top Cageplate | 1 | |
| 9 | 1393-37-03 | Front Cageplate Spacer | 2 | |
| 10 | 1393-23 | Guide Ring | 2 | |
| 11 | – | Jaw Assembly (11″ shown) | 2 | |
| 12 | 1393-1 | Rotary Gear | 1 | |
| 13 | 1393-22 | Bottom Cageplate | 1 | |
| 14 | 02-0017 | Backing Pin Knob | 1 | |
| 15 | 1393-39 | Backing Pin | 1 | |
| 16 | 09-5607 | 3/8″ NC Nylock Nut | 22 | |
| 17 | 09-0103 | 1/2″ x 1-3/4″ Shoulder Bolt | 22 | |
| Door Pivot Support Roller | ||||
| Components | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Straight Grease Fitting | 2 | |
| 2 | 09-9266 | 1″ Standard UNS Hex Nylock Nut | 2 | |
| 3 | 09-5120 | 1″ Narrow Washer | 2 | |
| 4 | 1393-140 | Shaft Spacer | 2 | |
| 5 | 1393-136 | NSK HR33206 J Tapered Roller Bearing | 2 | |
| 6 | 1393-131-3 | Support Roller Shaft | 1 | |
| 7 | 1393-134 | Support Roller Shaft Spacer | 1 | |
| 8 | 1393-135 | Support Roller | 1 | |
| Shifter Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 101-1749 | Shifter Handle | 1 | |
| 2 | 1393-71 | Shifting Shaft | 1 | |
| 3 | 02-0018 | Shifter Detent Ball | 2 | |
| 4 | 997-0-64 | Shifter Detent Spring | 2 | |
| 5 | 101-1497 | Threaded Shifter Detent Tube | 2 | |
| 6 | 09-5908 | 7/16″ UNF Hex Nut | 2 | |
| 7 | 09-1608 | 7/16″ UNF x 1-1/4″ Hex Bolt | 2 | |
| 8 | 09-7116 | 3/8″ x 1-1/2″ Clevis Pin | 2 | |
| 8 | BS 1574 5/64″ x 5/8″ Cotter Pin | 2 | ||
| 9 | Top Motor Mount Plate | |||
| 10 | 1393-78 | Lower Shifter Bushing | 1 | |
| 11 | 3/8″ x 1″ Thin Head Hex SHCS | 1 | ||
| 12 | Top Tong Plate | |||
| 13 | 1393-72 | Shifting For Weldment | 1 | |
| 14 | 1429-39-02 | 3/4″ NC Nylock Nut | 1 | |
| Tong Jaws | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 3/8″ NC x 1/2″ Hex Washer Head Machine Screw | 2 | ||
| 2 | Standard 5″ Die Insert | |||
| 3 | 1393-J-11000 | Jaw Weldment (11″ Shown) | 1 | |
| 4 | 1/4″ NC x 1/2″ Hex Flat Countersunk Cap Screw | 1 | ||
| 5 | 1393-JP | Jaw Pin | 1 | |
| 6 | 1393-JR-300 | Jaw Roller | 1 | |
| Farr Style Tong KT10750 | ||||
| Rinner GA15-15 Hydraulic Motor | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 1500-09-03A | Torque Gauge Mount Weldment | 1 | |
| 2 | 09-2166 | 1/2″ NC x 1″ Hex SHCS | 4 | |
| 3 | 02-9216 | 1-1/4″ (#20) Flange Elbow | 2 | |
| 4 | 02-9217 | 1-1/4″ (#20) Split Flange Kit | 2 | |
| 5 | 87-0112 | Rinner GA15-15 Hydraulic Motor | 1 | |
| 6 | 997-A10-149 | Motor Gear | 1 | |
| 7 | 09-5119 | 1/2″ Narrow Lockwasher | 1 | |
| 8 | 1/2″ NC x 3/4″ Hex Bolt | 1 | ||
| 9 | 02-0006 | 1/8″ NPT x 45 Degree Grease Fitting | 1 | |
| 10 | 09-2170 | 1/2″ NC x 1-1/2″ Hex SHCS | 4 | |
| 11 | 1116-150 | Motor Mount | 1 | |
| 12 | Hitch Pin .148 x 2.938 | 1 | ||
| 13 | 1500-09-04A | Torque Gauge Holder Weldment | 1 | |
| 14 | 09-0106 | 3/8″ NC x 3/8″ Set Screw | 2 | |
| Pinion Gear Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 09-1168 | 1/2″ NC x 1-1/4″ Hex Bolt | 8 | |
| 2 | 09-5110 | 1/2″ Carbon Steel Lockwasher | 8 | |
| 3 | 02-0006 | 1/8″ NPT x 45 Degree Grease Fitting | 4 | |
| 4 | 1050-89 | Bearing Cap | 2 | |
| 5 | 02-0007 | Deep Groove Ball Bearing | 2 | |
| 6 | 997-A4-87 | High Pinion Gear | 1 | |
| 7 | 997-A7-86 | Pinion Gear | 1 | |
| 8 | 997-A5-88 | Low Pinion Gear | 1 | |
| Pinion Idler Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Grease Fitting | 1 | |
| 2 | 09-5740 | 1-1/2″ UNF Nylock Nut | 1 | |
| 3 | 09-5040 | 1-1/2″ Flatwasher | 1 | |
| 4 | 09-1235 | 5/8″ NC x 2-1/4″ Hex Bolt | 3 | |
| 5 | 09-5114 | 5/8″ Carbon Steel Lockwasher | 3 | |
| 6 | 997-D17-109 | Pinion Idler Pad | 1 | |
| 7 | 1050-D5-105 | Idler Half-Shaft | 1 | |
| 8 | 02-0008 | Idler Bearing Retainer | 1 | |
| 9 | 02-0009 | Retainer Clip | 2 | |
| 10 | 997-A2-119 | Idler Gear | 1 | |
| 11 | 02-0011 | Idler Bearing | 1 | |
| Half-Roller Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0097 | 1/4″ UNF Straight Thread Grease Fitting | 1 | |
| 2 | 09-9167 | 1″ UNS Thin Nylock Nut | 1 | |
| 3 | 1116-143 | Half-Shaft Spacer | 1 | |
| 4 | 02-0094 | Ball Bearing | 1 | |
| 5 | 1116-144 | Roller Cup | 1 | |
| 6 | 1116-139 | Roller Half-Shaft | 1 | |
| Rotary Idler Assemly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0005 | 1/8″ NPT Grease Fitting | ||
| 2 | 09-5740 | 1-1/2″ UNF Nylock Nut | 2 | |
| 3 | 997-D20-125 | Rotary Idler Pad | 2 | |
| 4 | 1050-D5-121 | Rotary Idler Spacer | 2 | |
| 5 | 1050-D5-117 | Rotary Idler Shaft | 1 | |
| 6 | 02-0010 | Bearing Seal | 2 | |
| 7 | 02-0009 | Bearing Retainer | 2 | |
| 8 | 02-0011 | Idler Bearing | 1 | |
| 9 | 997-A2-119 | Idler Gear | 1 | |
| Support Roller Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0097 | 1/4″ UNF Straight Thread Grease Fitting | 2 | |
| 2 | 09-9167 | 1″ UNS Thin Nylock Nut | 2 | |
| 3 | 1037-C-140 | Roller Bearing Spacer | 2 | |
| 4 | 02-0014 | Support Roller Bearing | 2 | |
| 5 | 1037-131 | Support Roller Shaft | 1 | |
| 6 | 1037-C-134 | Inner Support Roller Spacer | 1 | |
| 7 | 1037-135 | Support Roller | 1 | |
| Door Pivot Roller Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0097 | 1/4″ UNF Straight Thread Grease Fitting | 2 | |
| 2 | 09-9167 | 1″ UNS Thin Nylock Nut | 2 | |
| 3 | 1037-C-140 | Roller Bearing Spacer | 2 | |
| 4 | 02-0014 | Support Roller Bearing | 2 | |
| 5 | 101-3482 | Door Pivot Roller Shaft | 1 | |
| 6 | 1037-135 | Support Roller | 1 | |
| 7 | 1037-C-134 | Inner Support Roller Spacer | 1 | |
| Rotary Gear Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 09-5607 | 3/8″ NC Nylock Nut | 1 | |
| 2 | 1116-36 | Rear Cageplate Bolt | 1 | |
| 3 | 09-1194 | 1/2″ NC x 7″ Hex Bolt | 2 | |
| 4 | 1050-C5-28 | Jaw Pivot Bolt | 2 | |
| 5 | 09-5110 | 1/2″ Lockwasher | 2 | |
| 6 | 1116-D-21 | Top Cageplate | 1 | |
| 7 | 09-0116 | 5/8″ x 1-1/2″ Hex Shoulder Bolt | 18 | |
| 8 | 1050-C3-38 | Cageplate Spacer | 3 | |
| 9 | 1116-23 | Manganese Bronze Support Ring | 2 | |
| 10 | 1116-7A-T | Top Body Plate | 1 | |
| 11 | 09-5610 | 1/2″ NC Nylock Nut | 18 | |
| 12 | Jaw Die Kit Assembly | 2 | ||
| 13 | 1116-D-1 | Rotary Gear | 1 | |
| 14 | 1116-7A-B | Bottom Body Plate | 1 | |
| 15 | 1116-D-22 | Bottom Cageplate | 1 | |
| 16 | 02-0017 | backing Pin Knob | 1 | |
| 17 | 1116-40 | Backing Pin Retainer | 1 | |
| 18 | 1116-39 | Backing Pin | 1 | |
| Support Roller (Door | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0097 | 1/4″ UNF Straight Thread Grease Fitting | 2 | |
| 2 | 09-9167 | 1″ UNS Thin Nylcok Nut | 2 | |
| 3 | 02-0014 | Support Roller Bearing | 2 | |
| 4 | 101-3482 | Support Roller Shaft | 1 | |
| 5 | 1037-135 | Support Roller | 1 | |
| 6 | 1037-C-134 | Inner Support Roller Spacer | 1 | |
| Clutch Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 02-0001 | External Snap Ring Retainer | 1 | |
| 2 | 1116-A3-61 | Clutch Shaft Drive Bushing Gear | 1 | |
| 3 | 997-60 | Clutch Bearing Bushing | 1 | |
| 4 | 02-0002 | Top Clutch Bearing | 1 | |
| 5 | 09-9137 | #10 x 1″ Hex Socket Cap Screw | 2 | |
| 6 | 997-D11-59 | Top Bearing Retainer | 1 | |
| 7 | 1116-50-01 | Washer | 1 | |
| 8 | 997-A1-51 | High Clutch Gear | 1 | |
| 9 | 02-0003 | Needle Bearing | 4 | |
| 10 | 997-A8-50 | Clutch Shaft | 1 | |
| 11 | 09-1048 | 3/8″ NC x 1-1/4″ Hex Bolt | 4 | |
| 12 | 09-5106 | 3/8″ Carbon Steel Lockwasher | 4 | |
| 13 | 02-0006 | 1/8″ NPT x 45 Degree Grease Fitting | 4 | |
| 14 | 1050-C1-54 | Clutch Bearing Cap | 1 | |
| 15 | 02-0004 | Lower Clutch Bearing | 1 | |
| 16 | 997-A1-52 | Low Clutch Gear | 1 | |
| 17 | 997-A9-62 | Shifting Collar | 1 | |
| Shifter Assembly | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 09-0256 | Clevis Pin 5/16″ x 1-1/2″ | 2 | |
| 2 | 1037-D-20B | Shifter Handle Weldment | 1 | |
| 3 | 09-0274 | Hitch Pin Spaenaur CP-83H | 2 | |
| 4 | 09-1170 | 3/8″ NC x 1″ Hex Bolt | 4 | |
| 5 | 09-5106 | 3/8″ Lockwasher | 4 | |
| 6 | 101-0016 | Shifting Lug Weldment | 1 | |
| 7 | 1116-71 | Shifter Shaft | 1 | |
| 8 | 09-1108 | 7/16″ UNF x 1-1/4″ Hex Bolt | 1 | |
| 9 | 09-5808 | 7/16″ UNF Hex Nut | 1 | |
| 10 | 997-0-64 | Detent Spring | 1 | |
| 11 | 02-0018 | Detent Ball | 1 | |
| 12 | 1064-B1-94 | Top Shifter Bushing (Typically Welded to Top Plate) | 1 | |
| 13 | 1116-72 | Shifting Fork Weldment | 1 | |
| 14 | 09-5914 | 5/8″ UNF Jam Nut | 2 | |
| 15 | 1064-B1-95 | Bottom Shifter Bushing (Typically Welded to Bottom Plate) | 1 | |
| Tong Jaws | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 1116-JDK-170 | 3-1/2″ Jaw Die Kit | 2 | |
| 2 | 1116-JDK-175 | 4″ Jaw Die Kit | 2 | |
| 3 | 1116-JDK-180 | 4-1/2″ Jaw Die Kit | 2 | |
| 4 | 1116-JDK-185 | 5″ Jaw Die Kit | 2 | |
| 5 | 1116-JDK-190 | 5-1/2″ Jaw Die Kit | 2 | |
| 6 | 1116-JDK-193 | 6″ Jaw Die Kit | 2 | |
| 7 | 1116-JDK-680 | 6.050″ Jaw Die Kit | 2 | |
| 8 | 1116-JDK-195 | 6-5/8″ Jaw Die Kit | 2 | |
| 9 | 1116-JDK-200 | 7″ Jaw Die Kit | 2 | |
| 10 | 1116-JDK-201 | 7-3/8 Jaw Die Kit | 2 | |
| 11 | 1116-JDK-202 | 7.390″ Jaw Die Kit | 2 | |
| 12 | 1116-JDK-205 | 7-5/8″ Jaw Die Kit | 2 | |
| 13 | 1116-JDK-203 | 7.656″ Jaw Die Kit | 2 | |
| 14 | 1116-JDK-206 | 7-3/4″ Jaw Die Kit | 2 | |
| 15 | 1116-JDK-207 | 8-1/2″ Jaw Die Kit | 2 | |
| 16 | 1116-JDK-210 | 8-5/8″ Jaw Die Kit | 2 | |
| 17 | 1116-JDK-215 | 9-5/8″ Jaw Die Kit | 2 | |
| 18 | 1116-JDK-218 | 9-7/8″ Jaw Die Kit | 2 | |
| 19 | 1116-JDK-219 | 10-5/8″ Jaw Die Kit | 2 | |
| 20 | 1116-JDK-220 | 10-3/4″ Jaw Die Kit | 2 | |
| Foster Style Tongs 5893R | ||||
| Foster Style Backup 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | Backup Tool Assembly | 121.8 | 1 | |
| 2 | Backup Tool Assembly with Air Cylinder | 126 | 1 | |
| 3 | 11-131 | Grease Fitting 1/4″-28 | 0.01 | 7 |
| 4 | 11-145 | Stover Locknut, 5/8″-11 NC | 0.02 | 2 |
| 5 | 11-196 | Lockwasher, 3/8″ | 0.01 | 10 |
| 6 | 11-321 | 90° Elbow, 1/4″ (male to female) | 0.2 | 2 |
| 7 | 11-683 | Hex Head Capscrew, 3/8″ x 1-1/4″ | 0.05 | 10 |
| 8 | Stover Locknut, 3/8″ | 0.02 | 10 | |
| 9 | 11-806 | Lockwasher, 5/8″ | 0.02 | 2 |
| 10 | 11-878 | Allen Head Capscrew, 1/2″ x 1″ | 0.03 | 2 |
| 11 | High Collar Lockwasher, 1/2″ | 0.02 | 2 | |
| 12 | 11-995 | Allen Head Screw, 1/2″ x 1-1/4″ | 0.03 | 12 |
| 13 | 11-1335 | Dowel Pin, 1/2″ x 1-1/2″ | 0.01 | 5 |
| 14 | 11-1575 | Hex Head Capscrew, 5/8″ x 3-1/2″ | 0.02 | 2 |
| 15 | 12-126 | 1 Wire Air Hose 18″ Long, 1/4″ Male Pipe Both ends | 0.2 | 1 |
| 16 | Air Hose Quick Connect, 1/4″ (male end) | 0.01 | 1 | |
| 17 | 1 Wire Hose 5-1/2″ Long, 1/4″ Male Pipe x 1/4″ JIC Female Swivel | 0.8 | 2 | |
| 18 | 90° Elbow, 1/4″ Pipe to 1/4″ Male JIC | 0.2 | 2 | |
| 19 | 50-49-2 | Insert Screw, 3/8″ x 1-1/8″ | 0.02 | 10 |
| 20 | 105-100 | Backup Air Cylinder Assembly | 4 | 1 |
| 21 | Air Cylinder Clevis Pin, 1/2″ x 1-3/4″ | 0.03 | 2 | |
| 22 | Cotter Pin, 1/8″ x 1-1/4″ | 0.01 | 2 | |
| 23 | 121-10 | Backup Return Spring | 0.07 | 1 |
| 24 | 147-1-1 | Backup Ring Gear with Handles | 10.6 | 1 |
| 25 | 147-2-10 | Top Cap(6-1/4″ Bore) | 21.6 | 1 |
| 26 | Backup Housing with Arm | 51.8 | 1 | |
| 27 | 147-6 | Backup Jaw Pin | 0.4 | 5 |
| 28 | 147-7 | Backup Jaw, 2-3/8″ to 3-3/4″ | 2.41 | 5 |
| 29 | Backup Jaw Assembly, 2-3/8″ to 3-3/4″ | 3 | 5 | |
| 30 | 147-19 | Backup Housing Adapter | 5.8 | 1 |
| 31 | 147-20 | Backup Swivel Block | 9.4 | 1 |
| 32 | 147-40 | Front Positioner | 6.6 | 1 |
| 33 | 147-41 | Back Positioner | 9.2 | 1 |
| 34 | 147-43 | Front and Back Pull Pin, 1/2″ x 4-3/4″ | 0.2 | 2 |
| 35 | 195-6 | Backup Push-Pull Air Valve Assembly | 2.2 | 1 |
| 36 | 50-48-1 | Insert | 0.4 | 5 |
| 37 | 11-920 | Safety Pin | 0.01 | 2 |
| Foster Style Clutch Assembly 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 50-13-1 | Clutch Assembly | 18.41 | 1 |
| 2 | 819-1 | Anchor Pin | 0.03 | 1 |
| 3 | 819-5 | Split Ring | 0.01 | 4 |
| 4 | 819-9 | Pressure Plate | 0.56 | 2 |
| 5 | 819-10 | Inner Disc | 0.25 | 12 |
| 6 | 819-11 | Outer Disc | 0.13 | 14 |
| 7 | 819-12 | Thrust Plate | 1.2 | 2 |
| 8 | 819-13 | Adjustment Collar | 0.6 | 2 |
| 9 | 819-14 | Spring Pin | 0.02 | 6 |
| 10 | 819-16 | Separating Spring | 0.02 | 6 |
| 11 | 819-17 | Dog | 0.1 | 6 |
| 12 | 819-18 | Dog Pivot | 0.02 | 6 |
| 13 | Shipper Sleeve Pin | 0.03 | 6 | |
| 14 | 819-20 | Clutch Body | 4.2 | 1 |
| 15 | 819-21 | Shipper Sleeve | 3.6 | 1 |
| 16 | Clutch Pack Kit (PN 819-9 thru 819-14, 819-16) | 9.44 | 2 | |
| Foster Style Hanger Extension Assembly 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 58-60-4 | Hanger Extension Assembly | 46 | 1 |
| 2 | 58-71 | Compression Spring | 0.4 | 4 |
| 3 | 58-72 | Spring Guide | 0.1 | 8 |
| 4 | 58-91-1 | Compression Spring Bolt | 2 | 2 |
| 5 | Compression Spring Bolt Assembly | 4.4 | 2 | |
| 6 | 11-803 | Nut, 3/4″ | 0.13 | 6 |
| 7 | 123-27 | Pull Pin, 3/4″ x 8-1/2″ (not part of Assembly) | 1 | 2 |
| 8 | 11-920 | Safety Pin | 0.01 | 2 |
| Foster Style Lift Assembly 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | Hydraulic Lift Assembly | 210 | 1 | |
| 2 | 11-145 | Stover Locknut, 5/8″-11 NC | 0.02 | 2 |
| 3 | 11-806 | Lockwasher, 5/8″ | 0.02 | 2 |
| 4 | 58-71 | Compression Spring | 0.4 | 2 |
| 5 | 58-72 | Spring Guide | 0.1 | 8 |
| 6 | 58-91-1 | Compression Spring Bolt | 2 | 2 |
| 7 | Compression Spring Bolt Assembly | 4.4 | 2 | |
| 8 | 11-803 | Nut, 3/4″ | 0.13 | 6 |
| 9 | 123-27 | Pull Pin, 3/4″ x 8-1/2″ (not part of assembly) | 1 | 2 |
| 10 | 11-112 | Hex Head Capscrew, 5/8″ x 2-1/4″ | 0.01 | 4 |
| 11 | 11-148 | Operating Rod Shackle, 1/2″ (Clevis) | 0.6 | 1 |
| 12 | 11-317 | High Pressure Street Elbow, 3/8″ | 0.2 | 1 |
| 13 | 11-353 | O-Ring | 0.01 | 1 |
| 14 | 11-355 | O-Ring | 0.01 | 1 |
| 15 | 11-356 | O-Ring | 0.01 | 3 |
| 16 | 11-361 | O-Ring | 0.01 | 1 |
| 17 | 11-816 | Retainer Ring | 0.01 | 1 |
| 18 | 11-1076 | Castle Nut, 1-1/2 NF | 0.6 | 1 |
| 19 | 11-1153 | Cotter Pin, 1/4″ x 3″ | 0.01 | 1 |
| 20 | 12-130 | Lift Hose, 8″ | 2.2 | 1 |
| 21 | 123-1-1 | Top Lift Cap | 7.6 | 1 |
| 22 | Top Lift Cap Assembly | 9.4 | 1 | |
| 23 | 123-2-1 | Working Barrel | 104 | 1 |
| 24 | 123-3-1 | Operating Rod | 88 | 1 |
| 25 | 123-4 | Cup Retainer | 0.2 | 1 |
| 26 | 123-4-1 | Cup Retainer | 0.1 | 1 |
| 27 | 123-5-1 | Cup | 0.01 | 2 |
| 28 | 123-9 | Piston | 0.8 | 1 |
| 29 | 123-10 | Bumper Washer | 0.01 | 1 |
| 30 | 123-13-7 | Bottom End Assembly | 31.2 | 1 |
| 31 | 123-20 | Lift Repair Kit | 0.2 | 1 |
| 32 | 123-23 | Brass Bushing | 1.4 | 1 |
| 33 | 123-26 | Oil Seal | 0.6 | 1 |
| 34 | 126-7 | Cushion Spring | 19 | 1 |
| 35 | 136-8-1 | Spring Housing | 49 | 1 |
| 36 | 11-920 | Safety Pin | 0.01 | 2 |
| Foster Style Transmission Assembly 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 11-603 | Hex Head Cap Screw, 3/8″ x 1-1/4″ | 0.06 | 18 |
| 2 | 11-604 | Hex Head Cap Screw, 3/8″ x 3/4″ | 0.05 | 6 |
| 3 | 11-113 | Allen Head Cap Screw, 3/8″ x 1″ | 0.03 | 2 |
| 4 | 11-124 | Transmission Plate Dowel Pin, 5/16″ x 3/4″ | 0.02 | 4 |
| 5 | 11-176 | Hi-Pro Key No. 18 | 0.01 | 2 |
| 6 | 11-200 | Hex Head Capscrew, 5/16″ x 3/4″ | 0.04 | 12 |
| 7 | 11-299 | Drain Petcock Fitting | 0.03 | 1 |
| 8 | 11-349 | O-ring | 0.02 | 1 |
| 9 | 11-436 | 90° Elbow Fitting, 5/16″ Ferrule to 1/8″ Pipe (Brass) | 0.05 | 1 |
| 10 | Allen Set Screw, 3/8″ x 1/2″ | 0.01 | 1 | |
| 11 | 11-572 | Allen Head Cap Screw, 5/16″ x 3/4″ NF | 0.05 | 6 |
| 12 | 11-662 | Hex Head Cap Screw, 5/16″ x 1/2″ | 0.02 | 20 |
| 13 | 11-900 | Spirolox Ring | 0.01 | 3 |
| 14 | 11-1043 | Hex Head Cap Screw, 3/8″ x 1-1/4″ | 0.02 | 16 |
| 15 | 11-1132 | Cotter Pin, 1/8″ x 1-3/4″ | 0.01 | 1 |
| 16 | 11-1186 | Hi-Pro Key | 0.02 | 6 |
| 17 | 11-1492 | Hex Head Cap Screw, 1/2″ x 2-1/4″ | 0.2 | 2 |
| 18 | 18507 | High Clutch Gear | 3.8 | 1 |
| 19 | 18599 | Low Clutch Gear | 10.4 | 1 |
| 20 | 50-13-1 | Clutch Assembly | 18.41 | 1 |
| 21 | 50-20 | Ring Gear and Pinion | 6.2 | 1 |
| 22 | 50-28-3 | Shifting Fork | 4.4 | 1 |
| 23 | 50-32-1 | Bearing Assembly (PN 50-32-1A, 50-32-1B) | 1.4 | 3 |
| 24 | 50-45-1 | Bearing Spacer | 0.01 | 2 |
| 25 | 50-83 | Ring & Pinion Shim | 0.01 | 1 |
| 26 | 50-193 | Shifting Yoke | 0.6 | 1 |
| 27 | 56-81 | Oil Sight Gauge | 0.02 | 1 |
| 28 | 21459 | High Drive Gear | 4 | 1 |
| 29 | 58-14-2 | Clutch Shaft | 8.8 | 1 |
| 30 | 58-17-3 | Transmission End Plate | 12 | 1 |
| 31 | 58-23 | Bottom Bearing Cap | 3.4 | 1 |
| 32 | 58-23-1 | Top Bearing Cap with Hole | 3.2 | 1 |
| 33 | 58-25 | Bearing | 0.33 | 4 |
| 34 | 58-27-10 | Clutch Lever with Shaft | 8.2 | 1 |
| 35 | 58-29-1 | Back Bearing Cap | 3.4 | 1 |
| 36 | 58-37 | Motor Gasket | 0.01 | 1 |
| 37 | 58-137-1 | Pinion Spacer | 0.06 | 1 |
| 38 | 119-202 | Oil Pump Assembly | 4 | 1 |
| 39 | 58-255 | Transmission End Plate Gasket | 0.01 | 1 |
| 40 | 58-259 | Bearing Cap Gasket | 0.01 | 1 |
| 41 | 58-261 | Bearing Cap Gasket | 0.01 | 2 |
| 42 | 58-295 | Side Cover Plate | 1.4 | 2 |
| 43 | 58-363-1 | Castle Nut, 1″ | 0.1 | 1 |
| 44 | O-Ring Gasket | 0.03 | 2 | |
| 45 | 58-400 | Gasket Set | 0.01 | 1 |
| 46 | 71-200 | Ring Gear Gasket | 0.01 | 1 |
| 47 | 77-90 | Hydraulic Motor (standard) | 41.8 | 1 |
| 48 | 77-90-2 | Hydraulic Motor (High Torque) | 43.5 | 1 |
| 49 | 92-183 | Bearing Assembly | 1 | 1 |
| 50 | Motor Adapter Gasket (thin) | 0.01 | 3 | |
| 51 | Motor Adapter Gasket (thick) | 0.01 | 1 | |
| 52 | 34274 | Drive Shaft | 5.3 | 1 |
| 53 | 93-18 | Ring Gear Cover | 8 | 1 |
| 54 | 93-19 | Ring Gear Hub and Sprocket | 11.9 | 1 |
| 55 | 93-32 | Bearing Assembly | 2.5 | 1 |
| 56 | 93-37-2 | Motor Adapter | 3.2 | 1 |
| 57 | 93-114 | Oil Pump Discharge Line | 0.06 | 1 |
| 58 | 93-115 | Oil Line | 0.02 | 1 |
| 59 | 93-125 | Counter Balance Assembly | 176 | 1 |
| 60 | 93-166 | Hex Head Cap Screw, 3/8″ x 1″ | 0.1 | 14 |
| 61 | 93-183 | Bearing Assembly | 0.5 | 1 |
| 62 | 93-251 | Chain Side Cover Plate Gasket | 0.01 | 1 |
| 63 | 93-295-1 | Chain Side Cover Plate | 3.7 | 1 |
| 64 | 58-143-1 | Oil Pump Gear | 0.4 | 1 |
| 65 | 11-595 | Oil Pump Gear Set Screw, 5/16″ x 1/2″ | 0.01 | 2 |
| 66 | 11-196 | Lockwasher. 3/8″ | 0.01 | 10 |
| 67 | 11-321 | 90° Elbow, 1/4″ (Male to Female) | 0.2 | 2 |
| Foster Style Transmission Assembly 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | 11-603 | Hex Head Cap Screw, 3/8″ x 1-1/4″ | 0.06 | 18 |
| 2 | 11-604 | Hex Head Cap Screw, 3/8″ x 3/4″ | 0.05 | 6 |
| 3 | 11-113 | Allen Head Cap Screw, 3/8″ x 1″ | 0.03 | 2 |
| 4 | 11-124 | Transmission Plate Dowel Pin, 5/16″ x 3/4″ | 0.02 | 4 |
| 5 | 11-176 | Hi-Pro Key No. 18 | 0.01 | 2 |
| 6 | 11-200 | Hex Head Capscrew, 5/16″ x 3/4″ | 0.04 | 12 |
| 7 | 11-299 | Drain Petcock Fitting | 0.03 | 1 |
| 8 | 11-349 | O-ring | 0.02 | 1 |
| 9 | 11-436 | 90° Elbow Fitting, 5/16″ Ferrule to 1/8″ Pipe (Brass) | 0.05 | 1 |
| 10 | Allen Set Screw, 3/8″ x 1/2″ | 0.01 | 1 | |
| 11 | 11-572 | Allen Head Cap Screw, 5/16″ x 3/4″ NF | 0.05 | 6 |
| 12 | 11-662 | Hex Head Cap Screw, 5/16″ x 1/2″ | 0.02 | 20 |
| 13 | 11-900 | Spirolox Ring | 0.01 | 3 |
| 14 | 11-1043 | Hex Head Cap Screw, 3/8″ x 1-1/4″ | 0.02 | 16 |
| 15 | 11-1132 | Cotter Pin, 1/8″ x 1-3/4″ | 0.01 | 1 |
| 16 | 11-1186 | Hi-Pro Key | 0.02 | 6 |
| 17 | 11-1492 | Hex Head Cap Screw, 1/2″ x 2-1/4″ | 0.2 | 2 |
| 18 | 18507 | High Clutch Gear | 3.8 | 1 |
| 19 | 18599 | Low Clutch Gear | 10.4 | 1 |
| 20 | 50-13-1 | Clutch Assembly | 18.41 | 1 |
| 21 | 50-20 | Ring Gear and Pinion | 6.2 | 1 |
| 22 | 50-28-3 | Shifting Fork | 4.4 | 1 |
| 23 | 50-32-1 | Bearing Assembly (PN 50-32-1A, 50-32-1B) | 1.4 | 3 |
| 24 | 50-45-1 | Bearing Spacer | 0.01 | 2 |
| 25 | 50-83 | Ring & Pinion Shim | 0.01 | 1 |
| 26 | 50-193 | Shifting Yoke | 0.6 | 1 |
| 27 | 56-81 | Oil Sight Gauge | 0.02 | 1 |
| 28 | 21459 | High Drive Gear | 4 | 1 |
| 29 | 58-14-2 | Clutch Shaft | 8.8 | 1 |
| 30 | 58-17-3 | Transmission End Plate | 12 | 1 |
| 31 | 58-23 | Bottom Bearing Cap | 3.4 | 1 |
| 32 | 58-23-1 | Top Bearing Cap with Hole | 3.2 | 1 |
| 33 | 58-25 | Bearing | 0.33 | 4 |
| 34 | 58-27-10 | Clutch Lever with Shaft | 8.2 | 1 |
| 35 | 58-29-1 | Back Bearing Cap | 3.4 | 1 |
| 36 | 58-37 | Motor Gasket | 0.01 | 1 |
| 37 | 58-137-1 | Pinion Spacer | 0.06 | 1 |
| 38 | 119-202 | Oil Pump Assembly | 4 | 1 |
| 39 | 58-255 | Transmission End Plate Gasket | 0.01 | 1 |
| 40 | 58-259 | Bearing Cap Gasket | 0.01 | 1 |
| 41 | 58-261 | Bearing Cap Gasket | 0.01 | 2 |
| 42 | 58-295 | Side Cover Plate | 1.4 | 2 |
| 43 | 58-363-1 | Castle Nut, 1″ | 0.1 | 1 |
| 44 | O-Ring Gasket | 0.03 | 2 | |
| 45 | 58-400 | Gasket Set | 0.01 | 1 |
| 46 | 71-200 | Ring Gear Gasket | 0.01 | 1 |
| 47 | 77-90 | Hydraulic Motor (standard) | 41.8 | 1 |
| 48 | 77-90-2 | Hydraulic Motor (High Torque) | 43.5 | 1 |
| 49 | 92-183 | Bearing Assembly | 1 | 1 |
| 50 | Motor Adapter Gasket (thin) | 0.01 | 3 | |
| 51 | Motor Adapter Gasket (thick) | 0.01 | 1 | |
| 52 | 34274 | Drive Shaft | 5.3 | 1 |
| 53 | 93-18 | Ring Gear Cover | 8 | 1 |
| 54 | 93-19 | Ring Gear Hub and Sprocket | 11.9 | 1 |
| 55 | 93-32 | Bearing Assembly | 2.5 | 1 |
| 56 | 93-37-2 | Motor Adapter | 3.2 | 1 |
| 57 | 93-114 | Oil Pump Discharge Line | 0.06 | 1 |
| 58 | 93-115 | Oil Line | 0.02 | 1 |
| 59 | 93-125 | Counter Balance Assembly | 176 | 1 |
| 60 | 93-166 | Hex Head Cap Screw, 3/8″ x 1″ | 0.1 | 14 |
| 61 | 93-183 | Bearing Assembly | 0.5 | 1 |
| 62 | 93-251 | Chain Side Cover Plate Gasket | 0.01 | 1 |
| 63 | 93-295-1 | Chain Side Cover Plate | 3.7 | 1 |
| 64 | 58-143-1 | Oil Pump Gear | 0.4 | 1 |
| 65 | 11-595 | Oil Pump Gear Set Screw, 5/16″ x 1/2″ | 0.01 | 2 |
| 66 | 11-196 | Lockwasher. 3/8″ | 0.01 | 10 |
| 67 | 11-321 | 90° Elbow, 1/4″ (Male to Female) | 0.2 | 2 |
| Foster Style Tubing Tong 5893R | ||||
| Item # | Part Number | Description | Approx. Weight (lbs) | Qty Required |
| 1 | Hydraulic Powered Tubing Tong | 1450 | 1 | |
| 2 | 11-147 | Drag Ring Set Screw, 1″ x 1″ | 0.02 | 5 |
| 3 | Top Bearing Cap Dowel Pin 3/8″ x 7/8″ | 0.02 | 1 | |
| 4 | 11-324 | Square Head Pipe Plug 1-1/4″ | 0.2 | 2 |
| 5 | 11-601 | Allen Head Pipe Plug 1/2″ | 0.08 | 1 |
| 6 | 11-603 | Hex Head Cap Screw 3/8″ x 1-1/4″ | 0.06 | 18 |
| 7 | 11-604 | Hex Head Cap Screw 3/8″ x 3/4″ | 0.05 | 6 |
| 8 | 11-632 | Hex Head Cap Screw 3/8″ x 1-1/2″ | 0.06 | 6 |
| 9 | Long Insert Screw with Nut | 0.03 | 10 | |
| 10 | 11-859 | Square Head Set Screw 3/8″ x 1-1/2″ | 0.06 | 2 |
| 11 | 11-1160 | Hex Head Cap Screw, 3/8″ x 2-1/2″ | 0.1 | 12 |
| 12 | 18477 | Drag Ring Jaw Pin | 1.2 | 5 |
| 13 | 50-15-2 | Drag Ring Assembly, 5″ bore, 1″ Pin | 40.2 | 1 |
| 14 | 50-22-7 | Jaw, 2-3/8″ x 3-1/2″ | 4.4 | 5 |
| 15 | Jaw Assembly, 2-3/8″ x 3-1/2″ | 5.6 | 5 | |
| 16 | 50-57 | Drag Ring Spring | 0.02 | 5 |
| 17 | 50-58 | Drag Ring Plug | 0.01 | 5 |
| 18 | 58-47 | Oil Seal | 0.8 | 2 |
| 19 | 58-100 | Wear Band | 0.4 | 2 |
| 20 | 58-256 | Top Bearing Cap Gasket | 0.01 | 1 |
| 21 | 58-263 | Bottom Bearing Cap Gasket | 0.01 | 2 |
| 22 | 34003 | Top Bearing Cap | 50.2 | 1 |
| 23 | 34061 | Final Drive Gear | 105 | 1 |
| 24 | 34096 | Guide Bell, 5″ Bore | 32.2 | 1 |
| 25 | pull Pin, 3/4″ x 5-1/2″ | 0.8 | 2 | |
| 26 | 34151 | Roller Bearing | 10.6 | 2 |
| 27 | 93-13 | Base Ring | 0.6 | 2 |
| 28 | 93-25 | Bottom Bearing Race | 32.72 | 1 |
| 29 | 93-26 | Roller Chain Assembly | 16.6 | 1 |
| 30 | 93-30 | Seal Protector | 0.8 | 1 |
| 31 | 93-122 | Hanger Cover Plate | 3.4 | 1 |
| 32 | 93-161 | Cover Plate, 1″ Pin Hole, 5″ Bore | 17.8 | 1 |
| 33 | 93-285 | Drag Ring Sleeve | 17.6 | 1 |
| 34 | 93-286-1 | Bottom Bearing Cap | 35.2 | 1 |
| 35 | 93-287-3 | Bottom Bearing Cap Assembly (PN 11-196, 11-632, 93-285, 93-286-1) | 53.54 | 1 |
| 36 | 854-8 | Roller Chain Master Link | 0.4 | 1 |
| 37 | Case | 232 | 1 | |
| 38 | 50-149-6-100 | Jaw and Insert Assembly, 1-5/16″ to 1.9″, 1″ Pin Hole | 5.26 | 5 |
| 39 | 50-149-6 | Jaw, 1-5/16″ to 1.9″, 1″ Pin Hole | 4.8 | 5 |
| 40 | 50-48-5 | Insert | 0.2 | 10 |
| 41 | 58-330-100 | Jaw and Insert Assembly, 2-1/16″ to 2-3/8″, 1″ Pin Hole | 6.06 | 5 |
| 42 | 58-330 | Jaw, 2-1/16″ to 2-3/8″, 1″ Pin hole | 5.6 | 5 |
| 43 | 58-328 | Insert | 0.2 | 10 |
| 44 | 50-22-11 | Jaw and Insert Assembly, 3-1/2″ to 4-1/2″, 1″ Pin Hole | 4.03 | 5 |
| 45 | Jaw, 2-7/8″ to 5″, 1″ Pin Hole | 3 | 5 | |
| 46 | Insert, 3-1/2″ to 4-1/2″ | 1 | 5 | |
| 47 | Insert Screw, 3/8″ x 2-5/8″ with Nut, 3/8″ | 0.03 | 5 | |
| 48 | 58-160-2 | Drag Ring Assembly, 6-1/4″ bore, 1″ Pin | 34.8 | 1 |
| 49 | 34100 | Guide Bell, 6-1/4″ Bore | 31 | 1 |
| 50 | 93-161-3 | Cover Plate, 6-1/4″ Bore, 1″ Pin Hole | 15.4 | 1 |
| 51 | 50-22-12 | Jaw and Insert Assembly, 4″ to 5″, 1″ Pin hole | 4.53 | 5 |
| 52 | Insert, 4″ to 5″ | 1.5 | 5 | |
| 53 | 58-314 | Jaw (Solid), 5″ to 6-1/16″, 1″ Pin hole | 4 | 5 |
| 54 | 58-154-2 | Jaw and Insert Assembly, 4″ to 4-1/2″, 3/4″ Pin hole | 3.03 | 5 |
| 55 | Jaw,4″ to 5-1/2″, 3/4″ Pin hole | 1.8 | 5 | |
| 56 | Insert, 4″ to 4-1/2″ | 1.8 | 5 | |
| 57 | Insert Screw, 5/16″ x 2-5/8″ with Nut, 5/16″ | 0.03 | 5 | |
| 58 | 58-160-1 | Drag Ring Assembly, 7-1/4″ Bore, 3/4″ Pin | 25.8 | 1 |
| 59 | 34101 | Guide Bell, 7-1/4″ Bore | 30.1 | 1 |
| 60 | 93-161-1 | Cover Plate, 7-1/4″ Bore, 3/4″Pin Hole | 12.2 | 1 |
| 61 | Insert, 5″ to 5-1/2″ | 0.6 | 5 | |
| 62 | 58-336 | Jaw (Solid) 6-5/8″, 5/8″ Pin Hole | 4.3 | 10 |
| 63 | 58-332-2 | Drag Ring Assembly, 7-7/8″ Bore, 5/8″ Pin, 10 Pin | 25.8 | 1 |
| 64 | 34103 | Guide Bell, 7-7/8″ Bore | 30 | 1 |
| 65 | 93-161-8 | Cover Plate, 7-7/8″ Bore, 5/8″Pin Hole, 10 Pin | 12 | 1 |
| 66 | 58-331 | Jaw (Solid) 7″ , 5/8″ Pin Hole | 3 | 10 |
| 67 | 21398 | Drag Ring Jaw Pin, 3/4″ x 6-1/4″ | 0.6 | 5 |
| 68 | 58-57 | Drag Ring Plug | 0.03 | 5 |
| 69 | 50-57-1 | Drag Ring Spring | 0.05 | 5 |
| 70 | 11-583 | Drag Ring Set Screw | 0.06 | 5 |
| 71 | 50-58-1 | Drag Ring Plug | 0.6 | 5 |
| 72 | 21763 | Drag Ring Jaw Pin, 5/8″ x 6″ | 0.9 | 5 |
| 73 | 59-64 | Drag Ring Plug | 0.03 | 5 |
| 74 | 59-53 | Drag Ring Spring | 0.02 | 5 |
| 75 | 11-131 | Grease Fitting 1/4″-28 | 0.01 | 7 |
| 76 | 11-196 | Lockwasher, 3/8″ | 0.01 | 10 |
| 77 | 11-683 | Hex Head Cap Screw, 3/8″ x 1-1/4″ | 0.05 | 10 |
| 78 | Stover Locknut, 3/8″ | 0.02 | 10 | |
| 79 | 50-48-1 | Insert | 0.4 | 5 |
| 80 | 11-920 | Safety Pin | 0.01 | 2 |
FarrTong3
Posted in InventoryList.