| MODEL | MAX SIZE(IN) | MAX TORQUE(FT-LB) | WEIGHT(LBS) | DIMENSION (IN) | TORQUE ARM(IN) | MAX SPEED(RPM) |
| 45000 | 4.75 | 6670 | 620 | 31*43*26 | 23 | 97 |
| 55000 | 4.75 | 8740 | 620 | 31*43*26 | 23 | 102 |
| 56000 | 4.75 | 11750 | 620 | 31*43*26 | 23 | 77 |
OPEN HEAD TUBING TONG PARTS LIST
| item | PN# | Name | |
| 1 | 45016 | Thrust washer | |
| 2 | 45026 | IDLER GEAR | |
| 3 | 45028 | Thrust washer | |
| 4 | 45029 | Thrust washer | |
| 5 | 45030 | Guide roller shaft | |
| 6 | 45031 | Guide roller shaft | |
| 7 | 45033 | Thrust washer | |
| 8 | 45034 | Thrust washer | |
| 9 | 45040 | Guide roller | |
| 10 | 45042 | 103 tooth rotor | |
| 11 | 45048 | Pinion shaft | |
| 12 | 45050 | 29tooth high speed pinion | |
| 13 | 45051 | 14tooth low speed pinion | |
| 14 | 45052 | Retaining ring | |
| 15 | 45057 | 35tooth base | |
| 16 | 45058 | 20tooth hub | |
| 17 | 45134 | Inner gear | |
| 18 | 45140 | Planet gear | |
| 19 | 45277 | Large roller | |
| 20 | 45278 | Small roller | |
| 21 | 45279 | Roller bushing | |
| 22 | 45280 | Roller pin | |
| 23 | 45287 | Inner ring | |
| 24 | 55026 | Idler gear | |
| 25 | 55050 | 20tooth high speed pinion | |
| 26 | 55051 | 13tooth low speed | |
| 27 | 55056 | 35tooth base right hand | |
| 28 | 55057 | 35tooth base, left hand | |
| 29 | 55058 | 11tooth hub | |
| 30 | 56287 | ||
| 31 | 60106 | Lifting lever for CANVINS spider | |
| 32 | 65106 | Lifting lever for CANVINS spider | |
| 33 | 451135-048 | Motor shaft | |
| 34 | 45291A | 2 3/8”jaw | |
| 35 | 45291B | 2 7/8”jaw | |
| 36 | 45291C | 3 1/2” jaw | |
| 37 | 45291D | 4 1/2”jaw | |
| 38 | 45291E | 4” jaw | |
| 39 | 45291K | 3 3/4”jaw | |
| 40 | 45291T | 4 1/8’jaw | |
| 41 | 45292A | 2 3/8”jaw | |
| 42 | 45292B | 2 7/8”bushing | |
| 43 | 45292C | 3 1/2”bushing | |
| 44 | 45292D | 4 1/2”bushing | |
| 45 | 45292E | 4”bushing | |
| 46 | 45292K | 3 3/4”bushing | |
| 47 | 45292T | 4 1/2”bushing |
SE58 Closed head Tubing Tong is with variable torque, hydraulic lift, Pressure oil bath lubrication, hardened internal gears, roller chain final drive and two-speed operation. Because they are closed head, the power tong stay on the pipe all the way up. You save time because you don’t have to remove and replace the tongs on the pipe after each joint is pulled. Every joint is gripped with a uniform, predetermined torque between 0.41～8.13kN.m (300～6000 ft. lbs), which is controlled by setting the pressure relief valve. It is interchangeable with foster tubing tong. We are able to provide same Jaw and bushing parts.
Technical Parameter
- Application Rang: 60～89mm (23/8″ ～ 5″） tubing
- Maximum passing diameter: 127mm (5″)
- Torque: 0.41～8.13kN.m (300～6000 ft. lbs)
- High Gear Rated Torque: 0.41～1.76kN.m (300～1300 ft. lbs)
- Low Gear Rated Torque: 8.13kN.m (6000 ft. lbs)
- High Gear Rated Speed: 126r/min Low Gear Rated Speed: 27r/min
- Total Length：1295mm (51″) Thickness of Master Tong: 242mm (91/2″)
High of Master Tong and Backup Tong: 425mm (163/4″)
- Maximum dimension of glide elevator: 762mm (30″)
- Versa dint of the knot tail rope: 930kg (2056lbs)
- Distance of between Tubing center and the knot tail rope: 762mm (30″)
- Weight： 456kg (1000lbs)
- Rated System Pressure: 13MPa (1880psi)
- Maximum Oil Supply: 126L/min (33.5gpm)
SPARE PARTS FOR FOSTER 58-93R CLOSED HEAD HYDRAULIC TUBING TONG
| 93-26 three row chain |
| 58-47 oil seal wear bands |
| 93-7 roller bearing |
| 58-14 clutch shaft |
| 819-1 anchor pin |
| 819-5 split ring |
| 819-13 adjust collar |
| 819-9 pressure plate |
| 58-20 ring gear and pinion |
| 93-295 side plate |
| 919-11 outer disc |
| 819-10 inner disc |
| 147-1 ring gear |
| 50-48-1 inserts |
| 77-90 hydraulic motor |
| 58-240 hydraulic valve |
| 93-3-3 transmission case or tong case |
| 867-23 lever for valve |
| 93-4 final drive gear |
| 93-285drag ring sleeve |
| 50-12low clutch gear |
| 50-9high clutch gear |