rigparts272

Power Supply

Three phase 690V – 50Hz/60Hz, 48V

Frequency converter can achieve 20Hz to the rated frequency of regulation

The number of poles

There are 6 commonly used, the other is very custom

In accordance with the following provisions of Europe

Low voltage 89/336/CE; electromagnetic compatibility 73/23/CE

Refer to the following standards

EN600034-1, EN50081-1, EN50081-2, EN50082-1, EN50082-2

performance

In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department.

centrifugal force

Max up to 50000Kgf (490KN).

Output centrifugal force adjustment range 0 to 100%

Mechanical protection

According to EN60529, IEC529 regulations: IP66

Earthquake protection

According to EN50102, IEC68 regulations: IK08

Insulation grade

F Class (155 C); H Class (180 C) to be customized

Heat resistance

Manufacturing process using drip plastic forming

ambient temperature

From -30 to +40 degrees Celsius, the use of other environmental temperature with the manufacturers to confirm

A thermal protector

The standard vibrator is 130 DEG C (DIN44081-44082) thermistor thermistor for temperature protection or other anti frosting heater, please contact with the factory.

install

In any position can be installed, two vibrators connected by joint coupling

lubrication

All have been filling in vibrator factory lubricating oil, under normal conditions without the addition of lubricating oil, but under heavy conditions, frame size 35 and above models need to add the lubricating oil and the vibrator

Junction box

For fixing an electrical connection wire, a terminal with a special shape can be provided for fixing the power cord to avoid joint loosening.

Electric machinery

The three-phase asynchronous motor, designed to meet the vibration of the machine when starting the required maximum starting torque and torque curve design, frame size to AF33, 35 of the vibrator are vacuum injection molding process, vibrator frame more by plastic molding manufacturing.

Shell

Vibrator shell frame size 35 below the high strength Aluminum Alloy, frame size greater than using ductile iron 35, special shape design patent is beneficial to heat radiation, under normal conditions, full load operation when the temperature is much lower.

Bearing base

Ductile iron or gray cast iron.

Bearing flange flange Bearing

Ductile cast iron. The geometric structure of the flange can transmit the load to the outer shell.

Bearing Bearings

Special customization, tailored specifically for Italvibras, is applicable for both axial and radial loads.

Motor shaft shaft Motor

Aluminum alloy constant temperature quenching treatment, can reduce the stress. One end shaft extends out to connect the coupling.

Eccentric block weights Eccentric

The centrifugal force can be continuously adjusted, and the centrifugal force is indicated by the percentage of the centrifugal force. A patent system called ARS (patent number: M098A000194) can prevent the adjustment error.

Eccentric block end cap covers Weight

The Aluminum Alloy material from the shaft end of the eccentric block cover is divided into two pieces, so that can open the cover even two eccentric vibrator are connected together

Paint Painting

Spray salt test with epoxy resin powder for 500 hours at 200 C.

Power Supply

Three phase 690V – 50Hz/60Hz, 48V

Frequency converter can achieve 20Hz to the rated frequency of regulation

The number of poles

There are 6 commonly used, the other is very custom

In accordance with the following provisions of Europe

Low voltage 89/336/CE; electromagnetic compatibility 73/23/CE

Refer to the following standards

EN600034-1, EN50081-1, EN50081-2, EN50082-1, EN50082-2

performance

In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department.

centrifugal force

Max up to 50000Kgf (490KN).

Output centrifugal force adjustment range 0 to 100%

Mechanical protection

According to EN60529, IEC529 regulations: IP66

Earthquake protection

According to EN50102, IEC68 regulations: IK08

Insulation grade

F Class (155 C); H Class (180 C) to be customized

Heat resistance

Manufacturing process using drip plastic forming

ambient temperature

From -30 to +40 degrees Celsius, the use of other environmental temperature with the manufacturers to confirm

A thermal protector

The standard vibrator is 130 DEG C (DIN44081-44082) thermistor thermistor for temperature protection or other anti frosting heater, please contact with the factory.

install

In any position can be installed, two vibrators connected by joint coupling

lubrication

All have been filling in vibrator factory lubricating oil, under normal conditions without the addition of lubricating oil, but under heavy conditions, frame size 35 and above models need to add the lubricating oil and the vibrator

Junction box

For fixing an electrical connection wire, a terminal with a special shape can be provided for fixing the power cord to avoid joint loosening.

Electric machinery

The three-phase asynchronous motor, designed to meet the vibration of the machine when starting the required maximum starting torque and torque curve design, frame size to AF33, 35 of the vibrator are vacuum injection molding process, vibrator frame more by plastic molding manufacturing.

Shell

Vibrator shell frame size 35 below the high strength Aluminum Alloy, frame size greater than using ductile iron 35, special shape design patent is beneficial to heat radiation, under normal conditions, full load operation when the temperature is much lower.

Bearing base

Ductile iron or gray cast iron.

Bearing flange flange Bearing

Ductile cast iron. The geometric structure of the flange can transmit the load to the outer shell.

Bearing Bearings

Special customization, tailored specifically for Italvibras, is applicable for both axial and radial loads.

Motor shaft shaft Motor

Aluminum alloy constant temperature quenching treatment, can reduce the stress. One end shaft extends out to connect the coupling.

Eccentric block weights Eccentric

The centrifugal force can be continuously adjusted, and the centrifugal force is indicated by the percentage of the centrifugal force. A patent system called ARS (patent number: M098A000194) can prevent the adjustment error.

Eccentric block end cap covers Weight

The Aluminum Alloy material from the shaft end of the eccentric block cover is divided into two pieces, so that can open the cover even two eccentric vibrator are connected together

Paint Painting

Spray salt test with epoxy resin powder for 500 hours at 200 C.

Power Supply

Three phase 690V – 50Hz/60Hz, 24V

Single phase 100V-130V, 60Hz

200V-240V, 50Hz

Frequency converter can achieve 20Hz to the rated frequency of regulation

The number of poles

2 pole or 4 pole

In accordance with the following provisions of Europe

Low voltage ATEX; 94/9/EC 2006/95/EC

Refer to the following standards

61241-0 IEC/EN, 61241-1 EN, 60034-1. IEC/EN

performance

In the maximum eccentric force and the maximum power supply, can be continuous operation, but also can be interrupted. It depends on the type of vibrator and operating environment. For more information, please contact our technical department.

centrifugal force

Max up to 311Kgf (3.05KN), centrifugal force can be adjusted by the adjustable eccentric block

Mechanical protection

According to EN60529, IEC529 regulations: IP66

Earthquake protection

According to EN50102, IEC68 regulations: IK08

Insulation grade

F Class (155 C)

Heat resistance

Vacuum injection molding process

ambient temperature

From -20 to +40 C, the other temperature needs to be customized.

A thermal protector

Please customize with a thermal detector 130 C thermal protector (DIN4408144082)

install

In any position can be installed in the junction box, and the vibrator bottom, mounting holes on the same side.

lubrication

Fully sealed ball bearings, using lifetime lubrication.

Junction box

Used for fixing the electric connecting wire and strengthening the structure of the junction box, which can prevent the internal explosion. Can provide a special shape of the terminal, used to fix the power cord to avoid joint loosening.

Electric machinery

Three phase induction motor, stator coil using vacuum injection molding, the rotor is aluminum die casting

Shell

Aluminum alloy with good ductility and good ductility.

Bearing flange

Nodular cast iron, the structure can make the load evenly transmitted to the shell.

Motor shaft shaft Motor

Aluminum alloy constant temperature quenching treatment, can reduce the stress

Eccentric block weights Eccentric

Can be convenient to adjust the vibration power from 0 to 100%

Eccentric block end cap covers Weight

The Aluminum Alloy casting high strength and surface by sandblasting treatment

VBB-326-W VBB-546-W VBB-1076-W VBB-20156-W VBB-32246-W VBB-4

VBB-314-W VBB-534-W VBB-1054-W VBB-1684-W VBB-20114-W VBB

VB-50308-W VB-75558-W VB-100758-W VB-135908-WA VB-1601108-W

VB-112-W VB-322-W VB-552-W VB-1082-WA VB-10102-W VB-20182-W

VB-314-W

VB-534-W   vibratory motor

VB-634-W

VB-1054-WA

VB-1264-W

VB-1584-W

VB-20114-W

VB-32154-W

VB-50234-W

VB-75374-W

VB-80554-W

VB-84554-W

VB-100634-W

VB-145894-W

VBB series flameproof vibration motor is the use of the company’s successful technology VB Series vibration motor, flameproof and foreign advanced technology, the technology explosion and vibration technology, designed specifically for oilfield solids control equipment and design products, protective shell rating of IP55, insulation class F, Ex logo ExdⅡBT4, places for class ⅱ T4 group flammable gas or vapor and air to form an explosive mixture in the oil field <a
VBB series flameproof vibration motor, power 0.2 ~ 13KW, 2,4,6,8 very exciting force is 3 ~ 180KN, a total of 25 specifications.