SW Ideco T-1600 parts
| 1 | LINER, GASKET DUO URETHANE, FOR OIL BASED MUD, F/IDECO MUD PUMP T-1600, SOUTHWEST, P/N AJO507U, SCN: CC009247 | Each | 40 | |
| 2 | SEAL, URETHANE FOR WEARPLATE, & MODULE HI-TEMP, SOUTHWEST, T OILFIELD PRODUCTS P/N, 2988-U, FOR IDECO MUD PUMP MDL T-1600 , P/N 2988U | Each | 40 | |
| 3 | LINER, SEAL, 6-1/2″ , URETHANE, FOR MUD PUMP, P/N 2974-7U, SOUTHWEST | Each | 20 | |
| 4 | PLATE, LINER, WEAR, FOR IDECO MUD PUMP, NOV, P/N 8407-10 , IDECO | Each | 10 | |
| 5 | HOSE, LINER COOLING, PUMP, SOUTHWEST OILFIELD , P/N 1200H30 | Each | 10 | |
| 6 | BUSHING, VALVE GUIDE, 12P160, SOUTHWEST | Each | 20 | |
| 7 | INSERT,VALVE, GUIDE,NATIONAL OILWELL , NOV, P/N 551-105-09 | Each | 20 |
| 1. | Discharge valve, 4th complete 1560136 | EA | 5 | |
| 2. | Suction valve 1560126 | EA | 5 | |
| 3. | Plunger, 4” HC 340204 | EA | 5 | |
| 4. | Seal for stuffing box 2410031-342 | EA | 5 | |
| 5. | Packing 4 x 4-3/4” 6422346 | EA | 5 | |
| 6. | Falk, coupling 1030110 | EA | 3 | |
| 7. | Seal 2410031-429 | EA | 5 | |
| 8. | Packing 6422337 | EA | 5 | |
| 9 | Part N0: 5L-3979 CAT for Export pump-3 (EP-3) alternator charging belt | EA | 5 | |
| 10 | Lubricator pump belt 12.5 x 1300-A49 | EA | 5 |
Accumulator spare parts
| DQ045 | ||||
| 1 | Air line lubricator | 1 1/2″NPT P/N：60250120 | Each | 1 |
| 2 | Pressure test unit release valve | Valve relief, 9/16″ 20000 PSI 9/16″ T （Parker 20SM9071-GY WP 20000PSI） | Each | 1 |
| 3 | test unit pressure recorder | Model：WSSR-15 | Each | 1 |
| DQ046 | ||||
| 1 | AED Battery | SN:NT18C-C14-00197 LOT14NT18C-05 | Each | 1 |
| 2 | Ring Gasket | RX39 | Each | 10 |
| 3 | Ring Gasket | R57 | Each | 2 |
| 4 | Cup Tester Seal CUP | TYPE F CUP TYPE BOP TESTER,13-3/8″ CASING, 68- 72 LB/FT CASING WEIGHT RANGE | Each | 1 |
| 5 | Repair Kit Air operated Pump | (Include Air Motor and Fluid end R. Kit) | Each | 1 |
| 6 | 15 minutes SABA Fabric Lanyard with Hose | Each | 15 | |
| 7 | Swivel, 2″ | LSG S50, 2″ 1502 M x 2″ 1502 F, H2S, FMC, 3143916, 10000 CWP | Each | 2 |
| 8 | 9-5/8″ Casing circulation sub | 9-5/8″ LTC (pin) * 4-1/2″ IF (box) | Each | 1 |
| DQ047 | ||||
| 1 | DQ047 4″TWCV seal | Cameron P/N:664276-32 REV A01 | Each | 1 |
| 2 | AED Chargeable battery and charge | As Per Picture | Each | 1 |
| 3 | DQ047 Double pin High pressure fitting | 1 1/2″ NPT-1″NPT (male to male)*5000psi | Each | 4 |
| DQ048 | ||||
| 1 | pulse generator PC card | P/N：308-p-011 | Each | 1 |
| 2 | pilo sequencer PC card | P/N：308-s-014 | Each | 1 |
| 3 | Propane Jet Nozzle | PN：PJN-01 | Each | 3 |
| 4 | Repair kit for regulator FAIL SAFE F5R-1500-0-15 | PN:40500999 | Each | 1 |
| 5 | nuts, For 2 1/16″-5K FLANGE | 36mm | Each | 16 |
| 6 | nuts, For 3 1/8″-5K FLANGE | 46mm | Each | 16 |
| WAREHOUSE/OFFICE | ||||
| 1 | SWIVEL | C&C 70MPa 2″1502 M* 2″1502 F Trim to H2S 15000PSI 12 FEET | Each | 5 |
| 2 | SWIVEL | 50 F-M 70MPa 2″1502 M* 2″1502 F Trim to H2S 15000PSI | Each | 2 |
| 3 | SWIVEL | 50 F-M 70MPa 2″1502 M* 2″1502 F Trim to H2S 15000PSI | Each | 2 |
| 4 | SWIVEL | 50 F-M 70MPa 2″1502 M* 2″1502 F Trim to H2S 15000PSI | Each | 2 |
| 5 | low torque valve | 70MPa 2″weco1502F*M | Each | 10 |
VARCO TDS10SA Parts
| 1 | O-RING, P/N: 51300-381-B | pc. | 1 | |
| 2 | O-RING, P/N: 51300-273-B | pc. | 1 | |
| 3 | RETAINER RING, P/N: 30117775-2 | pc. | 1 | |
| 4 | RETAINER OIL SEAL, P/N: 119359 | pc. | 1 | |
| 5 | SEAL METAL CLAD, P/N: 77039 P/N: ON DAMAGED SEAL: 21699-3606 | pc. | 1 | |
| 6 | BUSHING, TURCITE, P/N: 119358 | pcs. | 2 | |
| 7 | RING, THRUST, P/N: 30119357 | pc. | 1 | |
| 8 | CLYD RING ROTARY 10.000 ROD, P/N: 118375 | pcs. | 10 | |
| 9 | CLYD RING ROTARY 11.500 ROD, P/N: 30119143 | pc. | 1 | |
| 10 | SEAL, P/N: 77039 | pc. | 1 |
| 1 | AIR SUSPENSION ASSEMBLY | AIR SUSPENSION ASSEMBLY, SPECIFICATION NO:P0900025AA | P0900025AA | Piece | 4 |
| 2 | FRONT SUSPENSION ASSEMBLY | INCLUDE THE FOLLOWING: | Z02040000005AA | Set | 2 |
| 1. FIXED ROD, FRONT AXLE(FRONT)SPECIFICATION NO: Z02040100001AA, 2. RUBBER LINER ASSEMBLY, TIE BAR SPECIFICATION NO: Z02040400002AA, | |||||
| 3. PIN SHAFT, TIE BAR SPECIFICATION NO: | |||||
| P2200137AA, | |||||
| 4. LOCK NUT M24X1.5 SPECIFICATION NO: 4316500024, | |||||
| 5. FLAT WASHER, TIE BAR SPECIFICATION NO: P1000095AA, As PER ATTACHED DRAWING | |||||
| 3 | FRONT STEEL PLATE SPRING ASSEMBLY | AS PER ATTACHED DRAWING | 5001200001 | Set | 2 |
| 4 | MANUAL BRAKE VALVE | AS PER ATTACHED DRAWING | 5000100085 | Piece | 2 |
| 5 | PRESSURE GAGE M12 0-16MPA | PRESSURE GAGE M12 0-16MPA | Piece | 2 | |
| 6 | MOTOR OF 3T WINCH AND REPAIR KIT | MOTOR OF 3T WINCH AND REPAIR KIT | Piece | 2 | |
| 7 | SEAL FOR STUFFING BOX | As per drawing item no 13 | HG4-337-66 | Piece | 6 |
| 8 | SEAL BETWEEN SHAFT AND STUFFING BOX CONNECTOR | As per drawing item no 6 | KR129.90.05.04 | Piece | 2 |
| 9 | BEARING FOR STUFFING BOX | As per drawing item no 12 | GB/T 2761994, 6214 125X70X24 | Piece | 4 |
| 10 | BEARING FOR STUFFING BOX | As per drawing item no 27 | GB/T 2761994 , 6213 120X65X23 | Piece | 4 |
| 11 | SPRING | As per drawing item no 16 | KR129.90.05.08 | Piece | 4 |
| 12 | SEAL FOR STUFFING BOX | As per drawing item no 14 | HG4-337-66 | Piece | 6 |
| 13 | SEAL FOR STUFFING BOX | As per drawing item no 15 | HG4-337-66 | Piece | 6 |
| 14 | SHAFT FOR STUFFING BOX | As per drawing item no 7 | KR129.90.05.05 | Piece | 1 |