| LANZHOU LS-NATIONAL OIL WELL PETROLEUM ENGINEERING CO. LTD. | ||
| ZP 175 ZP205 ZP275 ZP375 ROTARY TABLE PARTS LIST | ||
| ZP175 ROTARY TABLE PARTS LIST | ||
| Part Name | Part NO. | |
| ROTARY TABLE | 105.11.00-1 | |
| Lock pawl—left | 105.06.01 | |
| Lock pawl—right | 105.06.02 | |
| Pin,handle lock pawl | 105.06.03-1 | |
| Grease fitting | GB1152-89 (Ml 0X1) | |
| Grease fitting | ||
| Pin, lock pawl | 105.11.01 | |
| Plug | 105.06.05 (1/8″) | |
| Screw, hex soc hd | 105.06.10.00 | |
| Grease fitting | GB70-85 (M24X75) | |
| Plate, I.D | 105.11.27 | |
| Screw | GB67-85 (M4X8) | |
| Dipstick,oi1 | 105.11.10.00 | |
| Plug | 105.06.07 (1 1/2″) | |
| Housing | 105.11.20.00 | |
| Tongue | 105.11.03 | |
| Cover | 105.11.30.00 | |
| Ring gear (spiral teeth) | 105.11.31 | |
| Ring gear (beveling teeth) | 105.11.28 | |
| Bearing | 91682/530 | |
| Table | 105.11.05-1 | |
| Table installation | ||
| Ring gear (sprial teeth) | ||
| Table | ||
| Bearing | ||
| Columnar pin | ||
| Support, bearing | ||
| ROTARY TABLE | 105.11.00-1 | |
| 0-Ring | ||
| Screw | ||
| Washer, spring | ||
| Shim | ||
| Shim | ||
| Shim | ||
| Lock pawl | 105.11.50.00 | |
| Pin | 105.11.24 | |
| Pin, cotter 5X36 | GB91-86 | |
| Pin,cotter 5X36 | ||
| Kelly bushing | 105.11.30 (3 1/2″) | |
| Kelly bushing | 105.11.32 (5″) | |
| Kelly bushing installatior | ||
| Kelly bushing | ||
| Board | ||
| Pin | ||
| Master bushing | 105.11.29 | |
| Bearing | 1689/520 | |
| Shim | ||
| Shim | ||
| Shim | 105.11.10 | |
| Pinion shaft assembly | 105.11.40.00 | |
| Drain plug | ||
| Seal | 105.11.18 | |
| 0-Ring | 105.11.14 | |
| Screw | 105.11.17 (M20X65) | |
| Washer,spring 20 | GB93-87 | |
| Shim | 105.11.15 | |
| Shim | 105.11.16 | |
| Support,bearing | 105.11.12 | |
| Screw | GB5783-86 (Ml 6X40) | |
| Washer, spring 16 | GB93-87 | |
| SIinger | 105.11.13 | |
| 0-Ring | 105.11.11 | |
| Chain wheel | 105.11.2H | |
| Sprocket retainer | ||
| Flange | 105.11.19 | |
| Main kelly bushing installation | ||
| Main kelly bushing | ||
| Spacer | ||
| Board | ||
| Screw | ||
| Nut | ||
| Washer,sping 28X35X2 | ||
| ValveDN32 (1 1/4″) | ||
| Joint R1 1/4 | ||
| ROTARY TABLE | 105.11.00-1 | |
| Pinion Shaft Assembly | 105.11.40.00 | |
| Pinion Shaft Assembly | 105.11.40.00 | |
| Pinion (beveling teeth) | 105.11.40.12 | |
| Pinion (spiral teeth) | 105.11.40.13 | |
| Retainer,pinion end | ||
| End-plate of bearing | 105.11.40.02 | |
| Bearing | 32622EH | |
| 0-Ring | 105.11.40.03 | |
| Spacer | 105.11.40.04 | |
| Drain plug 1″ | ||
| Drain plug | 105.08.60.01 | |
| Magnet | 105.08.60.02 | |
| Pin, cotter 2X12 | GB91-86 | |
| Shaft,pinion | 105.11.40.05 | |
| Bearing | 53622H | |
| Screw | ||
| Screw | GB5783-86 (M20X60) | |
| Screw | GB5783-86 (Ml 6X50) | |
| Washer,spring 20 | ||
| Washer,spring 20 | GB93-87 | |
| Washer, spring 16 | GB93-87 | |
| Shim | 105.11.40.06 | |
| Capsule | 105.11.41.00 | |
| Shim | 105.11.40.07 | |
| Pinion Shaft Assembly | 105.11.40.00 | |
| Sea 1, o i 1 | D7-1-67 (140X170X15) | |
| Retainer,pinion end | ||
| Retainer,pinion end | 105.11.40.10 | |
| Nut,pinion shaft | ||
| Pinion shaft housing | 105.11.40.08 | |
| Key | 105.11.40.09 | |
| Sprocket retainer | C6-3-92 (125) | |
| Screw with head holes | ||
| Screw with head holes | GB32.1-88 | |
| Screw with head holes | ||
| Wire | ||
| Shim | ||
| Shim | ||
| Screw with head holes | ||
| ZP205 ROTARY TABLE PARTS LIST | ||
| Part Name | ||
| ROTARY TABLE | 105.07.00 | |
| Lock pawl—left | 105.06.01 | |
| Lock pawl—right | 105.06.02 | |
| Pin,handle lock pawl | 105.06.03-1 | |
| Grease fitting | GB1152-89 ( M10X1) | |
| Grease fitting | ||
| Pin, lock pawl | 105.07.0H | |
| Plug | 105.06.05 (1/8″) | |
| Screw, hex soc hd | 105.06.10.00 | |
| Grease fitting | GB70-85 (M24X75) | |
| Plate, I.D | 105.07.19 | |
| Screw | GB67-85 (M4X8) | |
| Dipstick,oi1 | 105.07.40.00 | |
| Plug | 105.06.07 (1 1/2″) | |
| Housing | 105.07.10.00 | |
| Tongue | 105.06.08 | |
| Cover | 105.07.20.00 | |
| Ring gear (spiral teeth) | 105.07.21 | |
| Ring gear (beveling teeth) | 105.07.20 | |
| Bearing | 1687/650 | |
| Table | 105.07.06 | |
| Table installation | ||
| Ring gear (sprial teeth) | ||
| Table | ||
| Bearing | ||
| Columnar pin | ||
| Support, bearing | ||
| ROTARY TABLE | 105.07.00 | |
| 0-Ring | ||
| Screw | ||
| Washer, spring | ||
| Shim | ||
| Shim | ||
| Shim | ||
| Lock pawl | 105.05.18 | |
| Pin | 105.05.19 | |
| Pin, cotter 5X36 | GB91-86 | |
| Pin,cotter 5X36 | ||
| Kelly bushing | 105.06.31 (5″) | |
| Kelly bushing | ||
| Kelly bushing installatior | ||
| Kelly bushing | ||
| Board | ||
| Pin | ||
| Master bushing | 105.07.22 | |
| Bearing | 1687/620 | |
| Shim | 105.07.08 | |
| Shim | ||
| Shim | ||
| Pinion shaft assembly | 105.07.30.00 | |
| Drain plug | 104.05.19 | |
| Seal | 105.07.09 | |
| 0-Ring | 105.07.10 | |
| Screw | 105.07.17 (M20X70) | |
| Washer,spring 20 | GB93-87 | |
| Shim | 105.07.11 | |
| Shim | 105.07.12 | |
| Support,bearing | 105.07.13 | |
| Screw | GB5783-86 (Ml 6X45) | |
| Washer, spring 16 | GB93-87 | |
| SIinger | 105.07.14 | |
| 0-Ring | 105.07.15 | |
| Chain wheel | 105.07.16 | |
| Sprocket retainer | 105.06.24 | |
| Flange | 105.06.25 | |
| Main kelly bushing installation | ||
| Main kelly bushing | ||
| Spacer | ||
| Board | ||
| Screw | ||
| Nut | ||
| Washer,sping 28X35X2 | ||
| ValveDN32 (1 1/4″) | ||
| Joint R1 1/4 | ||
| ROTARY TABLE | 105.07.00 | |
| Pinion Shaft Assembly | 105.07.30.00 | |
| Pinion Shaft Assembly | 105.07.30.00 | |
| Pinion (beveling teeth) | 105.07.30.10 | |
| Pinion (spiral teeth) | 105.07.30.11 | |
| Retainer,pinion end | 105.06.51.00 | |
| End-plate of bearing | ||
| Bearing | 32630 | |
| 0-Ring | D4-5-73 (420X8.6) | |
| Spacer | 105.07.30.03 | |
| Drain plug 1″ | 104.05.19 | |
| Drain plug | ||
| Magnet | ||
| Pin, cotter 2X12 | ||
| Shaft,pinion | 105.07.30.04 | |
| Bearing | 3630 | |
| Screw | GB5783-86 (M20X70) | |
| Screw | ||
| Screw | ||
| Washer,spring 20 | GB93-87 | |
| Washer,spring 20 | ||
| Washer, spring 16 | ||
| Shim | 105.06.50.04 | |
| Capsule | 105.07.30.05 | |
| Shim | 105.07.30.06 | |
| Pinion Shaft Assembly | 105.07.30.00 | |
| Sea 1, o i 1 | D7-1-67 (180X220X15) | |
| Retainer,pinion end | 105.06.50.07 | |
| Retainer,pinion end | ||
| Nut,pinion shaft | 105.06.50.08 | |
| Pinion shaft housing | ||
| Key | 105.06.50.09-1 | |
| Sprocket retainer | C6-1-72 (150) | |
| Screw with head holes | GB32.1-88 | |
| Screw with head holes | ||
| Screw with head holes | ||
| Wire | ||
| Shim | 105.07.30.07 | |
| Shim | 105.07.30.08 | |
| Screw with head holes | ||
| ZP275 ROTARY TABLE PARTS LIST | ||
| Part Name | ||
| ROTARY TABLE | 105.06.00 | |
| Lock pawl—left | 105.06.01 | |
| Lock pawl—right | 105.06.02 | |
| Pin,handle lock pawl | 105.06.03-1 | |
| Grease fitting | GB1152-89 ( Ml 0X1) | |
| Grease fitting | ||
| Pin, lock pawl | 105.06.04-1 | |
| Plug | 105.06.05 (1/8″) | |
| Screw, hex soc hd | 105.06.10.00 | |
| Grease fitting | GB70-85 (M24X75) | |
| Plate, I.D | 105.06.30-1 | |
| Screw | GB67-85 (M4X8) | |
| Dipstick,oi1 | 105.06.20.00 | |
| Plug | 105.06.07 (1 1/2″) | |
| Housing | 105.06.30.00 | |
| Tongue | 105.06.08 | |
| Cover | 105.06.40.00 | |
| Ring gear (spiral teeth) | 105.06.33 | |
| Ring gear (beveling teeth) | 105.06.34 | |
| Bearing | 91682/800 | |
| Table | 105.06.10 | |
| Table installation | ||
| Ring gear (sprial teeth) | ||
| Table | ||
| Bearing | ||
| Columnar pin | ||
| Support, bearing | ||
| ROTARY TABLE | 105.06.00 | |
| 0-Ring | ||
| Screw | 105.06.22 | |
| Washer, spring | GB93-87 | |
| Shim | ||
| Shim | ||
| Shim | ||
| Lock pawl | 105.05.18 | |
| Pin | 105.05.19 | |
| Pin, cotter 5X36 | GB91-86 | |
| Pin,cotter 5X36 | ||
| Kelly bushing | 105.06.31 (5″) | |
| Kelly bushing | ||
| Kelly bushing installatior | ||
| Kelly bushing | ||
| Board | ||
| Pin | ||
| Master bushing | 105.06.32 | |
| Bearing | 1681/800 | |
| Shim | ||
| Shim | 105.06.13 | |
| Shim | ||
| Pinion shaft assembly | 105.06.50.00 | |
| Drain plug | 104.05.19 | |
| Seal | 105.06.14 | |
| 0-Ring | 105.06.15 | |
| Screw | 105.06.22 (M24X70) | |
| Washer,spring 20 | ||
| Shim | 105.06.16 | |
| Shim | 105.06.17 | |
| Support,bearing | 105.06.18 | |
| Screw | GB5783-86 (Ml 6X40) | |
| Washer, spring 16 | GB93-87 | |
| SIinger | 105.06.19 | |
| 0-Ring | 105.06.20 | |
| Chain wheel | 105.06A. 01-1 | |
| Sprocket retainer | 105.06.24 | |
| Flange | 105.06.25 | |
| Main kelly bushing installation | ||
| Main kelly bushing | ||
| Spacer | ||
| Board | ||
| Screw | ||
| Nut | ||
| Washer,sping 28X35X2 | ||
| ValveDN32 (1 1/4″) | ||
| Joint R1 1/4 | ||
| ROTARY TABLE | 105.06.00 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Pinion (beveling teeth) | 105.06.50.12 | |
| Pinion (spiral teeth) | 105.06.50.13 | |
| Retainer,pinion end | 105.06.51.00 | |
| End-plate of bearing | ||
| Bearing | 32630 | |
| 0-Ring | D4-5-73 (420X8.6) | |
| Spacer | 105.06.50.02 | |
| Drain plug 1″ | 104.05.19 | |
| Drain plug | ||
| Magnet | ||
| Pin, cotter 2X12 | ||
| Shaft,pinion | 105.06.50.03 | |
| Bearing | 3630 | |
| Screw | GB5783-86 (M20X60) | |
| Screw | ||
| Screw | ||
| Washer,spring 20 | GB93-87 | |
| Washer,spring 20 | ||
| Washer, spring 16 | ||
| Shim | 105.06.50.04 | |
| Capsule | 105.06.50.05-1 | |
| Shim | 105.06.50.06 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Sea 1, o i 1 | D7-1-67 (180X220X15) | |
| Retainer,pinion end | 105.06.50.07 | |
| Retainer,pinion end | ||
| Nut,pinion shaft | 105.06.50.08 | |
| Pinion shaft housing | ||
| Key | 105.06.50.09-1 | |
| Sprocket retainer | C6-1-72 (150) | |
| Screw with head holes | GB32.1-88 | |
| Screw with head holes | ||
| Screw with head holes | ||
| Wire | ||
| Shim | ||
| Shim | ||
| Screw with head holes | ||
| ZP275-2 ROTARY TABLE PARTS LIST | ||
| Part Name | ||
| ROTARY TABLE | 105.10.00 | |
| Lock pawl—left | 105.06.01 | |
| Lock pawl—right | 105.06.02 | |
| Pin,handle lock pawl | 105.06.03-1 | |
| Grease fitting | GB1152-89 ( Ml 0X1) | |
| Grease fitting | ||
| Pin, lock pawl | 105.06.04-1 | |
| Plug | 105.06.05 (1/8″) | |
| Screw, hex soc hd | 105.06.10.00 | |
| Grease fitting | GB70-85 (M24X75) | |
| Plate, I.D | 105.10.03 | |
| Screw | GB67-85 (M4X8) | |
| Dipstick,oi1 | 105.06.20.00 | |
| Plug | 105.06.07 (1 1/2″) | |
| Housing | 105.06.30.00 | |
| Tongue | 105.06.08 | |
| Cover | 105.06.40.00 | |
| Ring gear (spiral teeth) | 105.06.33 | |
| Ring gear (beveling teeth) | 105.06.34 | |
| Bearing | 91682/800 | |
| Table | 105.06.10 | |
| Table installation | ||
| Ring gear (sprial teeth) | ||
| Table | ||
| Bearing | ||
| Columnar pin | ||
| Support, bearing | ||
| ROTARY TABLE | 105.10.00 | |
| 0-Ring | ||
| Screw | 105.06.22 | |
| Washer, spring | GB93-87 | |
| Shim | ||
| Shim | ||
| Shim | ||
| Lock pawl | 105.05.18 | |
| Pin | 105.05.19 | |
| Pin, cotter 5X36 | GB91-86 | |
| Pin,cotter 5X36 | ||
| Kelly bushing | 105.06.31 (5″) | |
| Kelly bushing | ||
| Kelly bushing installatior | ||
| Kelly bushing | ||
| Board | ||
| Pin | ||
| Master bushing | 105.06.32 | |
| Bearing | 1681/800 | |
| Shim | ||
| Shim | 105.06.13 | |
| Shim | ||
| Pinion shaft assembly | 105.06.50.00 | |
| Drain plug | 104.05.19 | |
| Seal | 105.06.14 | |
| 0-Ring | 105.06.15 | |
| Screw | 105.06.22 (M24X70) | |
| Washer,spring 20 | ||
| Shim | 105.06.16 | |
| Shim | 105.06.17 | |
| Support,bearing | 105.06.18 | |
| Screw | GB5783-86 (Ml 6X40) | |
| Washer, spring 16 | GB93-87 | |
| SIinger | 105.06.19 | |
| 0-Ring | 105.06.20 | |
| Chain wheel | ||
| 105.10.01.00 | ||
| Sprocket retainer | 105.06.24 | |
| Flange | 105.06.25 | |
| Main kelly bushing installation | ||
| Main kelly bushing | ||
| Spacer | ||
| Board | ||
| Screw | ||
| Nut | ||
| Washer,sping 28X35X2 | ||
| ValveDN32 (1 1/4″) | ||
| Joint R1 1/4 | ||
| ROTARY TABLE | 105.10.00 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Pinion (beveling teeth) | 105.06.50.12 | |
| Pinion (spiral teeth) | 105.06.50.13 | |
| Retainer,pinion end | 105.06.51.00 | |
| End-plate of bearing | ||
| Bearing | GB283-64 (32630) | |
| 0-Ring | D4-5-73 (420X8.6) | |
| Spacer | 105.06.50.02 | |
| Drain plug 1″ | 104.05.19 | |
| Drain plug | ||
| Magnet | ||
| Pin, cotter 2X12 | ||
| Shaft,pinion | 105.06.50.03 | |
| Bearing | 3630 | |
| Screw | GB5783-86 (M20X60) | |
| Screw | ||
| Screw | ||
| Washer,spring 20 | GB93-87 | |
| Washer,spring 20 | ||
| Washer, spring 16 | ||
| Shim | 105.06.50.04 | |
| Capsule | 105.06.50.05-1 | |
| Shim | 105.06.50.06 | |
| Pinion Shaft Assembly | 105.06.50.00 | |
| Sea 1, o i 1 | D7-1-67 (180X220X15) | |
| Retainer,pinion end | 105.06.50.07 | |
| Retainer,pinion end | ||
| Nut,pinion shaft | 105.06.50.08 | |
| Pinion shaft housing | ||
| Key | 105.06.50.09-1 | |
| Sprocket retainer | C6-1-72 (150) | |
| Screw with head holes | GB32.1-88 | |
| Screw with head holes | ||
| Screw with head holes | ||
| Wire | ||
| Shim | ||
| Shim | ||
| Screw with head holes | ||
| ZP375 ROTARY TABLE PARTS LIST | ||
| Part Name | ||
| ROTARY TABLE | 105.08.00 | |
| Lock pawl—left | 105.06.01 | |
| Lock pawl—right | 105.06.02 | |
| Pin,handle lock pawl | 105.06.03-1 | |
| Grease fitting | ||
| Grease fitting | GB1152-89 (Ml 0x1) | |
| Pin, lock pawl | 105.08.10-1 | |
| Plug | 105.06.05 (1/8″) | |
| Screw, hex soc hd | 105.06.10.00 | |
| Grease fitting | GB70-85 (M24x75) | |
| Plate, I.D | 105.08.20 | |
| Screw | GB67-85 (M4x8) | |
| Dipstick,oi1 | 105.08.30.00 | |
| Plug | 105.06.07 (1 1/2″) | |
| Housing | 105.08.20.00 | |
| Tongue | 105.06.08 | |
| Cover | 105.08.10.00 | |
| Ring gear (spiral teeth) | ||
| Ring gear (beveling teeth) | ||
| Bearing | ||
| Table | ||
| Table installation | 105.08.40.00 | |
| Ring gear (sprial teeth) | 105.08.40.11 | |
| Table | 105.08.40.02 | |
| Bearing | 2687/1049 | |
| Columnar pin | 105.08.40.03 | |
| Support, bearing | 105.08.40.04 | |
| ROTARY TABLE | 105.08.00 | |
| 0-Ring | 105.08.40.05 | |
| Screw | GB70-85 (M24x60) | |
| Washer, spring | GB93-87 (24) | |
| Shim | 105.08.40.06 | |
| Shim | 105.08.40.07 | |
| Shim | 105.08.40.08 | |
| Lock pawl | 105.08.02 | |
| Pin | 105.05.19 | |
| Pin, cotter 5X36 | ||
| Pin,cotter 5X36 | GB91-86 (5×36) | |
| Kelly bushing | ||
| Kelly bushing | ||
| Kelly bushing installatior | 105.54.00 (2 3/8″~8 5/8″) | |
| Kelly bushing | 105.54.01 | |
| Board | 105.54.02 | |
| Pin | 105.54.03 | |
| Master bushing | ||
| Bearing | ||
| Shim | ||
| Shim | ||
| Shim | 105.08.08 | |
| Pinion shaft assembly | 105.08.50.00 | |
| Drain plug | ||
| Seal | ||
| 0-Ring | ||
| Screw | ||
| Washer,spring 20 | ||
| Shim | ||
| Shim | ||
| Support,bearing | ||
| Screw | GB5783-86 (Ml 6X35) | |
| Washer, spring 16 | GB93-87 (16) | |
| SIinger | 105.08.09 | |
| 0-Ring | ||
| Chain wheel | 105.08.07 | |
| Sprocket retainer | 105.08.14 | |
| Flange | 105.08.15 | |
| Main kelly bushing installation | 105.08.07.00 | |
| Main kelly bushing | 105.08.70.04 | |
| Spacer | 105.08.70.02 | |
| Board | 105.08.70.03 | |
| Screw | 105.08.03 | |
| Nut | 105.08.04 | |
| Washer,sping 28X35X2 | D3-3-67 (28x35x2) | |
| ValveDN32 (1 1/4″) | GB8465.1-87 (DN32 1 1/4″) | |
| Joint R1 1/4 | GB3289.26-82 (R1 1/4) | |
| ROTARY TABLE | 105.08.00 | |
| Pinion Shaft Assembly | 105.08.50.00 | |
| Pinion Shaft Assembly | 105.08.50.00 | |
| Pinion (beveling teeth) | ||
| Pinion (spiral teeth) | 105.08.50.12 | |
| Retainer,pinion end | ||
| End-plate of bearing | 105.08.50.09 | |
| Bearing | GB283-64 (32630) | |
| 0-Ring | 105.08.50.02 (470×8.6) | |
| Spacer | 105.08.50.04 | |
| Drain plug 1″ | 105.08.60.00 | |
| Drain plug | 105.08.60.01 (1″) | |
| Magnet | 105.08.60.02 | |
| Pin, cotter 2X12 | GB91-86 (2×12) | |
| Shaft,pinion | 105.08.50.03 | |
| Bearing | GB286-64 (3630) | |
| Screw | GB5783-86 (M20X60) | |
| Screw | ||
| Screw | ||
| Washer,spring 20 | GB93-87 (20) | |
| Washer,spring 20 | ||
| Washer, spring 16 | ||
| Shim | 105.08.50.05 | |
| Capsule | 105.08.51.00 | |
| Shim | 105.08.50.06 (4> 400/322 6 1) | |
| Pinion Shaft Assembly | 105.08.50.00 | |
| Sea 1, o i 1 | D7-1-67 (180X220X15) | |
| Retainer,pinion end | 105.08.50.07 | |
| Retainer,pinion end | ||
| Nut,pinion shaft | ||
| Pinion shaft housing | 105.08.50.10 | |
| Key | 105.08.50.08 | |
| Sprocket retainer | 105.08.50.11 (150) | |
| Screw with head holes | ||
| Screw with head holes | ||
| Screw with head holes | GB32.1-88 (HI 6×35) | |
| Wire | ||
| Shim | ||
| Shim | ||
| Screw with head holes | GB32.1-88 | |
| RG ZP 175 ZP205 ZP275 ZP375 ROTARY TABLE PARTS LIST | ||
| E704 Rotary table bearing and seals | ||
| 1 | Bearing 9069244 | GB303-64 |
| 2 | Bearing 313 | GB267-64 |
| 3 | Bearing 317 | GB267-64 |
| 4 | OIL seal 80x112x12 | HG4-692-67 |
| ZP1-90 Rotary table bearing and seals | ||
| 1 | Bearing 9069280 | GB0303-64 |
| 2 | Bearing 7708172 | |
| 3 | conical bearing 7618 | GB267-64 |
| 4 | conical bearing Wl$f 8|yfc 7619 | GB267-64 |
| 5 | U Type seals 120x150x14 | HG4-3392-66 |
| ZP135 Rotary table bearing and seals | ||
| 1 | Bearing LJC387S0 | |
| 2 | Bearing 97520 | GB299-86 |
| 3 | Bearing 42316 | GB283-87 |
| 4 | O ring 412×7 | GB3452.1-82 |
| 5 | O ring 387×7 | GB3452.1-82 |
| 6 | Oil seal PD 95x130x12 | HG4-692-67 |
| ZP175 Rotary table bearing and seals | ||
| 1 | Bearing 1689/520 | |
| 2 | Bearing 91682/530 | |
| 3 | Bearing 32622EH | GB283-87 |
| 4 | Bearing 53622H | GB2SS-87 |
| 5 | O ring 345×7 | GB3452.1-82 |
| 6 | O ring 645×7 | GB3452.1-82 |
| 7 | O ring 515×7 | GB3452.1-82 |
| 8 | Oil seal PD170x140x16 | HG4-692-67 |
| ZP205 Rotary table bearing and seals | ||
| 1 | Bearing 1689/620 | |
| 2 | Bearing 9186/600 | |
| 3 | Bearing 2626 | GB2S3-87 |
| 4 | Bearing53626 | GB286-64 |
| 5 | Bearing 7326 | GB297-84 |
| 6 | O ring 375×7 | GB3452.1-82 |
| 7 | O ring 1885×7 | GB3452.1-82 |
| 8 | O ring 2360×7 | GB3452.1-82 |
| 9 | Oil seal PD170x140x6 | HG4-692-67 |
| ZP275 Rotary table bearing and seals | ||
| 1 | Bearing 1681/800 | |
| 2 | Bearing 91682/800 | |
| 3 | Bearing 32630E | GB2S3-S7 |
| 4 | Bearing 53630 | GB28S-87 |
| 5 | O ring 180x220x15 | GB3452.1-82 |
| 6 | O ring 420×8.6 | GB3452.1-82 |
| 7 | O ring 1000×8.6 | GB3452.1-82 |
| 8 | O ring 800×8.6 | GB3452.1-82 |
| BOMCO Rotary table driver assembly parts list | ||
| Description | PN | |
| 1 | Base | BA705310-0100 |
| 2 | Floor board | BA705310-02 |
| 3 | Rotary table assembly | BA705308-0300 |
| 4 | Chain case | BA705308-0400 |
| 5 | Floor board I | BA705305-0200 |
| 6 | Machine oil lubrication system | BA505303-0800 |
| 7 | Brake tongs Assembly | BA505303-0500 |
| 8 | Pump system | BA505303-0600 |
| 9 | Hydraulic Pipeline System | BA505303-0400 |
| 10 | supporting pole | BA705305-0700 |
| 11 | platform A | BA705305-0800 |
| 12 | Bracket | BA705305-0900 |
| 13 | Positioned block | AZ502106-010300 |
| 14 | Bolt M36X140 | AZ502106-0104 |
| 15 | adjusting shim | AZ502106-0106 |
| 16 | Pin shaft Ф20×105 | AZ502106-0111 |
| 17 | guard | BA505303-0700 |
| 18 | drum Gear Coupling | BA505301-0400 |
| 19 | 1 1/2″-3 tightened chain device | T102-002.00 |
| 20 | mini pin 4X65 | T403-002 |
| 21 | supporting pole L=705 | BA705310-0001 |
| 22 | Nut M36 | 420402016360400000 |
| 23 | Nut M36 | 420402026360300000 |
| 24 | Bolt M24x95 | 420201011124095000 |
| 25 | Spring washer 24 | 420503011241600000 |
| 26 | Nut M24 | 420402016240400000 |
| Nut M24 | ||
| 27 | Bolt M24x75 | 420201011124075000 |
| 28 | Bolt M24x55 | 420201011124055000 |
| 29 | Chains 24S-4-106 | WG05706041 |
| 30 | Air filter C-M60X2 | |
| 31 | AC Motor 600KW | |
| ZDPE ROTARY TABLE PARTS LIST | ||
| ZP-375 Rotary Table (ZDPE) Parts list | ||
| Description | PN | |
| 1 | Lock pawl-left | 105.06.01 |
| 2 | Lock pawl-right | 105.06.02 |
| 3 | Pin, handle lock pawl | 105.06.03-1 |
| 4 | Grease fitting | GB1152-89-M10×1 |
| 5 | Pin, lock pawl | 105.08.10-1 |
| 6 | Plug | 105.06.05(1/8″) |
| 7 | Screw, hex soc hd | 105.06.10.00 |
| 8 | Grease fitting | GB70-85-M24×75 |
| 9 | Plate, l .D | 105.08.20 |
| 10 | Screw | GB67-85-M4×8 |
| 11 | Dipstick, oil | 105.08.30.00 |
| 12 | Plug | 105.06.07(1 1/2″) |
| 13 | Housing | 105.08.20.00 |
| 14 | Tongue | 105.06.08 |
| 15 | Cover | 105.08.10.00 |
| 18 | Table installation | 105.08.40.00 |
| 18.1 | Ring gear (spiral teeth) | 105.08.40.11 |
| 18.2 | Table | 105.08.40.02 |
| 18.3 | Bearing | 2687/1049 |
| 18.4 | Columnar pin | 105.08.40.03 |
| 18.5 | Support, bearing | 105.08.40.04 |
| 18.6 | O-Ring | 105.08.40.05 |
| 18.7 | Screw | GB70-85-M24×60 |
| 18.9 | Washer, spring | GB93-87-24 |
| 18.10 | Shim | 105.08.40.06 |
| 18.11 | Shim | 105.08.40.07 |
| 18.12 | Shim | 105.08.40.08 |
| 19 | Lock pawl | 105.08.02 |
| 20 | Pin | 105.05.19 |
| 21 | Pin, cotter 5×36 | GB91-86-5×36 |
| 22 | Kelly bushing installation | 105.54.00(23/8〞～85/8〞) |
| 22.1 | Kelly bushing | 105.54.01 |
| 22.2 | Board | 105.54.02 |
| 24 | Pin | 105.54.03 |
| 25 | Shim | 105.08.08 |
| 26 | Pinion shaft assembly | 105.08.50.00 |
| 35 | Screw | GB5783-86-M16×35 |
| 36 | Washer, spring 16 | GB93-87-16 |
| 37 | Slinger | 105.08.09 |
| 40 | Sprocket retainer | 105.08.14 |
| 41 | Flange | 105.08.15 |
| 42 | Main Kelly bushing installation | 105.08.07.00 |
| 42.1 | Main Kelly bushing | 105.08.70.04 |
| 42.2 | Spacer | 105.08.70.02 |
| 42.3 | Board | 105.08.70.03 |
| 43 | Screw | 105.08.03 |
| 44 | Nut | 105.08.04 |
| 45 | Washer, spring 28×35×2 | D3-3-67-28×35×2 |
| 46 | Valve DN32(11/4〞) | GB8465.1-87-DN32 |
| 47 | Joint R11/4 | GB3289.26-82(R11/4) |
| 2.Pinion Shaft Assembly | ||
| No. | Denomination | Drawing No. |
| Pinion Shaft Assembly | 105.08.50.00 | |
| 1 | Pinion (spiral teeth) | 105.08.12 |
| 2 | End-plate of bearing | 105.08.50.09 |
| 3 | Bearing | GB283-64-32630) |
| 4 | O-Ring | 105.08.50.02-470×8.6 |
| 5 | Spacer | 105.08.50.04 |
| 6 | Drain plug 1〞 | 105.08.60.00 |
| 6.1 | Drain plug 1〞 | 105.08.60.01(1〞) |
| 6.2 | Magnet | 105.08.60.02 |
| 6.3 | Pin, cotter 2×12 | GB91-86(2×12) |
| 7 | Shaft, pinion | 105.08.50.03 |
| 8 | Bearing | GB286-64-3630 |
| 9 | ScrewX | GB5783-86-M20×60 |
| 10 | Washer, spring 20 | GB893-87-20 |
| 11 | Shim | 105.08.50.05 |
| 12 | Capsule | 105.08.51.00 |
| 13 | Shim | 105.08.50.06 |
| 14 | Seal, oil | D7-1-67-180×220×15 |
| 15 | Retainer, pinion end | 105.08.50.07 |
| 16 | Pinion shaft housing | 105.08.50.10 |
| 17 | Key | 105.08.50.08 |
| 18 | Sprocket retainer | 105.08.50.11-150 |
| 19 | Screw with head holes | GB32.1-88-M16×35 |
| 23 | Screw with head holes | GB32.1-88-M20×45 |
Rotarytableparts2
Posted in InventoryList.