LANZHOU LS ZJ50 Rig Parts list
Lock pawl—left | 105.06.01 |
Lock pawl—right | 105.06.02 |
Pin,handle lock pawl | 105.06.03-1 |
Grease fitting | |
Grease fitting | GB1152-89 (M10x1) |
Pin,lock pawl | 105. 08. 10-1 |
Plug | 105.06.05 (1/8″) |
Screw, hex soc hd | 105.06.10.00 |
Grease fitting | GB70-85 (M24x75) |
Plate, I.D | 105.08.20 |
Screw | GB67-85(M4x8) |
Dipstick, oil | 105.08.30.00 |
Plug | 105.06.07 (1 1/2″) |
Housing | 105.08.20.00 |
Tongue | 105.06.08 |
Cover | 105. 08. 10. 00 |
Table installation | 105.08.40.00 |
Ring gear (sprial teeth) | 105.08.40.11 |
Table | 105.08.40.02 |
Bearing | 2687/1049 |
Columnar pin | 105. 08.40. 03 |
Support, bearing | 105. 08.40. 04 |
O-Ring | 105.08.40.05 |
Screw | GB70-85(M24*60) |
Washer, spring | GB93-87(24) |
Shim | 105.08.40.06 |
Shim | 105.08.40.07 |
Shim | 105.08.40.08 |
Lock pawl | 105.08.02 |
Pin | 105.05.19 |
Pin,cotter 5X36 | GB91-86(5*36) |
Kelly bushing instal1 at ion | 105.54.00(2 3/8″-8 5/8″) |
Kelly bushing | 105.54.01 |
Board | 105.54.02 |
Pin | 105.54.03 |
Shim | 105.08.08 |
Pinion shaft assembly | 105.08.50.00 |
Screw | GB5783-86(M16X35) |
Washer, spring 16 | GB93-87(16) |
SIinger | 105.08.09 |
Sprocket retainer | 105.08.14 |
Flange | 105.08.15 |
Main kelly bushing installation | 105.08.07.00 |
Main kelly bushing | 105.08.70.04 |
Spacer | 105.08.70.02 |
Board | 105.08.70.03 |
Sorew | 105.08.03 |
Nut | 105.08.04 |
Washer,spring 28X35X2 | D3-3-67(28*35*2) |
Valve DN32 (1 1/4″) | GB8465.1-87 |
Joint R11/4 | GB3289.26-82 |
Kellybushing 20″ | 105.08.21 |
Pinion shaft assembly | 105.08.50.00 |
| |
| 105.08.50.12 |
| |
End-plate of bearing | 105.08.50.09 |
Bearing | GB283-64 (32630) |
O-Ring | 105.08.50.02 (470*8.6) |
Spacer | 105.08.50.04 |
Drain plug 1″ | 105.06.60.00 |
Drain plug 1″ | 105.06.60.01 (1″) |
Magnet | 105.06.60.02 |
Pin,cotter 2X12 | GB91-86 (2×12) |
Shaft, pinion | 105.06.50.03 |
Bearing | GB286-64 (3630) |
Screw | GB5783-86 (M20X60) |
Screw | |
Screw | |
Washer,spring 20 | GB893-87(20) |
Washer,spring 20 | |
Washer,spring 16 | |
Shim | 105.08.50.05 |
Capsule | 105.08.51.00 |
Shim | 105.08.50.06(Ø400/322) |
Seal,oi | D7-1-67(180*220*15) |
Retainer, pinion end | 105.08.50.07 |
Retainer, pinion end | |
| |
Nut, pinion shaft | |
Pinion shaft housing | 105.08.50.10 |
Key | 105.08.50.08 |
Sprocket retainer | 105.08.50.11(150) |
Screw with head holes | |
Screw with head holes | |
Screw with head holes | GB32.1-88(M16*35) |
Wire | |
Shim | |
Shim | |
Screw with head holes | GB32.1-88 |